PCB suppliers for automotive programmes
For automotive work the certificate that matters is IATF 16949 issued to the specific manufacturing site, and the document that actually gates production is the PPAP package: control plan, PFMEA, MSA, initial process studies and a run-at-rate. A Chinese PCB factory without a written change-notification process is a bigger risk than one without the certificate.
Sector requirements reviewed 2026-11-11. See how we record evidence.
IATF 16949 belongs to a site, not to a company
The certificate names one manufacturing site, its address and its scope. A group with four plants can hold four certificates, or one certificate and three plants outside its scope — and buyers regularly quote a head-office certificate as if it covered all of them.
Two checks settle this in a minute:
- Read the site address on the certificate. It must be the address the boards ship from. If the certificate says Suzhou and the boards come from a plant in Jiangxi, the automotive controls do not follow the shipment.
- Check the certificate in the IATF database rather than accepting the PDF. Certificates are issued by IATF-recognised certification bodies and are searchable by company and site; a lapsed or withdrawn certificate is visible there.
There is also a scope question that matters more than it looks. IATF 16949 applies to sites manufacturing automotive parts. A PCB shop that runs one automotive line and nineteen consumer lines holds the certificate for the site, but the discipline is only as good as the line your order lands on. Ask which lines are in the automotive control plan.
PPAP is the real gate, and a bare board is not exempt
The Production Part Approval Process is where a Chinese board shop either has a system or improvises. The full submission has eighteen elements; for a PCB the ones that carry weight are:
| PPAP element | What a board shop actually submits |
|---|---|
| Design records | The fabrication drawing and stack-up at the approved revision, with the customer’s approval on it |
| PFMEA | Failure modes for drilling, plating, imaging, lamination and finish, with severity and detection ratings that are not all identical |
| Control plan | The parameter, the sample size, the frequency and the reaction plan for each critical step |
| MSA | Gauge repeatability for the measurements that appear on the drawing, not for a convenient subset |
| Initial process studies | Capability on the characteristics that matter — typically Ppk at or above 1.67 for a new process |
| Material and performance test results | Coupon data: plating thickness distribution, thermal stress, solderability, ionic contamination |
| Run-at-rate | Evidence that the line produces at the quoted rate, not only that it can produce one good lot |
The failure mode we see most: a supplier sends a neatly formatted PPAP with a control plan copied from another customer, PFMEA ratings that are all severity 5, and no reaction plan for out-of-control conditions. It passes a document review and fails the first process audit.
CQI-11 and CQI-12 are where plating shops get caught
The AIAG special process assessments for plating (CQI-11) and coating (CQI-12) are what automotive customers use to look inside a wet line. They cover tank chemistry control, rectifier calibration, rack maintenance, water quality, waste treatment and — most usefully — the evidence that the line is controlled by measurement rather than by the operator’s judgement.
A PCB factory that holds IATF 16949 but cannot produce a CQI-11 self-assessment, a plating thickness capability study and a calibration record for the rectifiers has a quality system without process control. For automotive work that gap shows up as thickness variation across the panel, which becomes solder-joint failure at the customer’s assembly plant six months later.
What automotive does to the board specification
The automotive requirement changes the board, not just the paperwork:
- Thermal cycling to the customer’s profile, commonly −40 °C to +125 °C or +150 °C, with the number of cycles written into the specification. The board has to survive the expansion mismatch between copper and laminate, which is a plating ductility question as much as a material one.
- CAF resistance. Conductive anodic filament growth between plated holes is the failure that ends automotive programmes quietly. It is tested to IPC-TM-650 2.6.25 and it depends on laminate, drill quality and desmear as a system.
- IST (interconnect stress test) for via reliability under combined thermal and current load, rather than thermal cycling alone.
- Ionic contamination control, because residues left by poor rinsing drive both corrosion and CAF.
- No touch-up. Hand rework of a Class 3 automotive board is generally prohibited; the process has to produce good boards, not fix bad ones.
A note on a common misconception: AEC-Q100 and AEC-Q200 do not apply to bare printed circuit boards. They qualify integrated circuits and passive components. A board shop claiming “AEC-Q100 certified boards” is either confusing its customers’ component qualification with its own process qualification, or using the term as marketing. The board-side equivalents are the IPC test methods and the customer’s own reliability specification.
Change notification: the clause that decides whether you have a supplier
The single most valuable sentence in an automotive supply agreement is the change notification clause. Any change to laminate, prepreg, plating chemistry, drill bit supplier, imaging equipment or the plant itself requires a notification and, usually, a new PPAP.
A supplier with no formal PCN process will make those changes silently, because from its side they are improvements. From your side they are a requalification event you did not get. When we assess a factory for automotive listing, we ask for a real PCN issued in the last two years. A supplier that cannot produce one has not been running the process.
Where this goes wrong in China
- IATF certificate quoted at group level. Read the site address and the scope.
- Automotive line, consumer discipline. The certificate covers the site; ask which lines are under the control plan.
- PPAP assembled from another customer’s file. Look for the customer-specific requirements, the reaction plan, and capability numbers that vary by characteristic.
- No CQI-11 assessment. Plating is the process automotive audits fail most often.
- AEC-Q claims for bare boards. A signal that the supplier is repeating marketing language rather than describing its process.
- No PCN. The most expensive gap, because it is invisible until something changes.
What we check before listing a factory for automotive
- IATF 16949 certificate: site address, scope, certification body, validity, checked in the IATF database.
- Whether the automotive line is identified and covered by a control plan, or whether the certificate is site-wide decoration.
- A CQI-11 self-assessment and plating capability data, where plating is in scope.
- The last PPAP submitted, and whether the PFMEA and control plan are specific to that part.
- A real PCN issued within the last two years.
- Reliability data on a comparable build: thermal cycling, CAF, IST, ionic contamination.
- Traceability from panel to date code, and the retention period in the contract.
Related: multilayer fabrication for the layer counts most automotive boards use, heavy copper and metal-core boards for thermal paths, testing for what a 100 percent electrical test actually covers, and the RFQ checklist for the questions that surface a weak process before you place an order.
Automotive: recorded factories
Ordered by evidence strength, then by most recent review. Each profile states what was checked, on what date, and which processes are subcontracted rather than performed on site. A listing is not a guarantee of factory ownership or certification validity.
Lanshun Technology (Shenzhen)
Lanshun lists 19 SMT machines and no board-making gear, yet its own table quotes 46 layers. Registered scope stops at assembly. Who makes the bare board?
SEIC (Shenzhen Shinelong Electronics)
SEIC pages say 75, 400 or 500 staff and put the plant at 1,800 or 12,000 square metres. A buyer's question list built from the differences.
Shanxu Precision Circuit (Shenzhen)
Shanxu says it began in 2003, but its Shenzhen entity dates to 2021 and a Jiangxi one to 2020. The capability table says 1-40 layers; the profile says 1-60.
Career Electronics (Kunshan)
Career's Kunshan FPC plant shows 945 insured staff in one record, 1,433 in another and 4,000+ in job ads. Two records name different legal representatives.
Huai'an Glorysky Electronics
The Huai'an plant of Glorysky has RMB 300m paid-in capital and 1,195 staff. Its business term ends in 2047 and its scope omits sales.
Huangshi WUS Electronics
Huangshi WUS has 4,017 staff and RMB 2.929bn 2024 revenue, and its licence explicitly says HDI production. Its industry code is C3969.
Jiangmen Suntak Circuit Technology
Suntak's Jiangmen subsidiary has RMB 800m paid-in capital, 2,532 staff and RMB 3.841bn 2025 revenue, with board production in its licence.
Jiangxi Kinwong Precision Circuit
Jiangxi Kinwong has 4,552 staff and a government case citing 8.78m m2 of annual capacity. Its licence files PCBs under new electronic components.
Junya Electronic Technology (Huizhou)
Junya 603386 says it runs six plants, yet its registered scope names components and materials, not PCBs. The Huizhou entity has 4,824 staff.
Kangyuan Electronics (Dongguan)
Kangyuan's site says 1977 and 100,000 m2; the registry says 2008, RMB 700m capital and 1,875 insured staff. The Nantong plant is a separate company.
Kunshan Dingxin Electronics
Kunshan Dingxin changed its legal representative and most of its board in July 2026, while a hiring page still names the previous one.
Kunshan Huliwei (WUS subsidiary)
WUS subsidiary Kunshan Huliwei has 2,135 staff and RMB 1.5bn capital, yet its licence says HDI boards are wholesale, not manufactured.
MFLEX (Suzhou Weixin Electronics)
MFLEX began in the US in 1984, listed on Nasdaq, and is now held through Singapore by DSBJ. The Suzhou entity has 7,256 staff; output spans three plants.
Multilayer PCB Technology (Shenzhen)
Mutailai moved its registered address to an office tower in 2025 and reports 61 staff, while its site claims 1,200 employees and four manufacturing sites.
Nantong Shennan Circuits
Nantong Shennan's 2026 plating and laser-drill tenders document live lines; its registry shows 3,990 staff and RMB 5.313bn 2025 revenue.
Shenlian Circuit (Shenzhen)
Shenlian's site claims four plants and 780,000 m2 a month. The Shenzhen entity has 1,217 staff and only added board production to its scope in 2023.
Stariver Circuit (Shenzhen plant)
Stariver's site describes a Shenzhen plant with 500 staff and 25,000 m2 a month. A similarly named Shenzhen company has one employee and a trading licence.
Wuxi Shennan Circuits
Wuxi SCC has 4,879 insured staff and RMB 780m paid-in capital. A 2026 stock-exchange report names it as the site of a RMB 4.6bn project.
Zhuhai Suntak Circuit Technology
Zhuhai Suntak is filed under I6520 IC design, yet its licence names double-sided, multilayer and flexible board production, with 2,201 staff.
Aohong Electronics
Two thirds of Aohong capacity is single-sided, unusual in a directory of multilayer factories. Its 12-layer sample is the highest count it shows.
Aoshikang Technology (Yiyang)
Aoshikang's 2024 output of 6.70 million m2 covers Zhaoqing and Thailand too; the Yiyang 6.00 million m2 is an EIA design limit, not output.
Apson Electronics (Xiamen)
Apson is 75% owned by listed Goproled; its own site claims 15,000 m2/month and 2/2 mil, the parent filing 15/15 um lines, a hiring page 100,000 m2/month.
AT&S China (Shanghai)
A Vienna-listed group's volume HDI line in Minhang, licensed for 970,000 m2 a year per a 2022 EIA - but IC substrates are Chongqing and Kulim business.
Avary Holding (Shenzhen)
Avary's 2018 listing document gives a Songgang factory as its address; the current registry gives a 27th-floor office in Bao'an.
Benchuan Intelligent Circuit (Nanjing)
Benchuan lists four production bases, but its Zhuhai plant was bought from DSBJ in 2024 for RMB 39.5m. The registry shows one address.
Bolion Tech (Xiamen)
Bolion quotes 16,000 m2/month on its company card and 30,000 on its hiring page, plus 16,700 from an old 200,000 m2/yr figure; three numbers, one plant.
Bomin Electronics
Bomin 52-layer and 7th-order HDI figures belong to the Meizhou Inno-Chip plant, whose phase-1 handover slipped to the end of 2026.
BYD Electronics
BYD Electronics publishes 165,000 employees, 10,000 engineers and no PCB capability. It assembles other people's boards at a scale that decides who it serves.
C-Flex (Huangshi Xipu Electronics)
Its single page claims first place in China for camera-module FPC by units shipped in 2024. No second source, no certificate numbers, no product pages.
Camelot Electronics (Qingyuan)
Camelot quotes 4.3m m2 of annual PCB capacity as of end-2025, but two new lines only started in July and September 2026. The figure is a snapshot.
CEE Technology (Zhongjing)
Zhongjing publishes 2026, 2027 and 2028 columns with sample and mass-production targets. Reading a number without its column quotes a board nobody builds.
CEE Yuansheng (Zhuhai)
Yuansheng filed for a ChiNext IPO in 2017, then was acquired by CEE, renamed and re-registered. Its best capacity data is still that old filing.
Chengde Electronic (Guangdong Chengde)
Chengde is NEEQ-listed with public financials. Its site quotes capacity in yuan, an industry profile in square metres, and two founding years disagree.
Chengzhiyi Circuit (Ji'an)
The Ji'an entity registered in 2022, but the profile quotes 2008, 30,000 m2 and 100,000 m2 a month as group figures without naming a site.
Cixi Qingbao Electronic Technology
Cixi Qingbao publishes 3 mil line/space; a 2026 Ningbo government article says 0.15 mm. Both are in print, neither is dated, and output figures differ too.
CMK Electronics (Wuxi) - CMK Corporation
CMK's Wuxi plant: 36,000 m2 a month or 480,000 m2 a year, and 670, 700 or 528 staff. The same CMK brand also names a different Dongguan company.
Compeq Huizhou (Boluo)
Compeq's 1995 Boluo plant holds 170,000 m2 and 3,200 staff, but the data-centre products sit with the Thai plant, not with Huizhou.
DBG Technology
DBG runs over 100 SMT lines in 13 bases across eight countries and buys its PCBs. That makes it an assembly candidate, not a PCB enquiry.
Delton Technology (Guangzhou)
A Hong Kong listing document says Guangzhou handles high-end server boards while Huangshi takes consumer and industrial work. The order split is written down.
Delton Technology (Huangshi)
A university visit page calls this the largest single PCB plant in the world. The company's own homepage gives 29,500 m2. Both cannot be right.
Dongguan Dingxin Circuit
Dingxin's milestone page ends at a 2018 Hunan plant, but filings show that plant was exited in 2023 and capital was cut in 2025.
Dongguan Lianqiao Electronics (L-Bridge)
A 16,000 m2 appliance-board plant that publishes real dimensions for four boards and dates for four of its five certificates. The fifth is contested.
Dongguan Viafull Circuit Technology
Viafull publishes UL file E466925, a checkable number, yet its own page quotes both 1-14 and 2-16 layers and 180 staff against 41 in filings.
Dongguan Yuejie Circuit Technology
Yuejie lists 64 layers, 10oz copper and IC substrates, yet its registry record shows three staff, four former names and a residential address.
DSBJ (Multek)
Multek publishes IATF and AS9100 certificates building by building, which almost nobody does. Its layer ceiling shifts four layers with the page language.
Dynamic Electronics (Huangshi)
Three years get quoted as this plant's founding: the group's 1988, the company's 2015, first output in 2017. Only the last one is a production date.
Ellington
Ellington publishes per-plant capacity, which is rare, and a certificate page whose latest expiry passed in 2025. Both matter for an automotive programme.
Flexium Interconnect (Kunshan) - Chunhua Technology
Every plant-level number for Flexium's Kunshan FPC site comes from one 2019 environmental report: 2.8 million m2 a year, 41,174 m2 of land, 6,000 staff.
Gaodeng Electronics (Yiyang)
The brand is a 1991 Hong Kong group, but Hunan Gaodeng is a domestic LLC held by natural persons; its 300,000 m2 a month is a target, not a verified output.
Goworld (CCTC)
Goworld PCB business sits inside a group that also makes LCDs and instruments. Three Shantou plants do different work, and only PCB counts as PCB output.
Heshan TTE Circuit
Heshan TTE's published capacity spans six figures, from an existing 130,000 m2/yr to an 800,000 m2/yr full-build target. Only one is a current licence.
Hongxin Electronics (Xiamen)
Hongxin's 2.18m m2/yr FPC capacity is group-consolidated; the Xiamen three-site EIA design figure is 1.05m m2/yr, and the plant is being reassigned.
Huatianhua Electronics (Xiamen)
Huatianhua's only capacity table is from a 2013 phase-two project: 30,000 m2/month single-sided, 10,000 double, 1,000 multilayer. No newer figure is public.
Huizhou Glorysky Electronics
Glorysky's process table runs three year columns: 32 layers now, 36 in 2027 and 78 in 2028. Directories quote the last column as if it were today.
JCD (Jingchengda)
Jingchengda's Chinese profile claims 2,000 staff and two plants; its English page says 860 staff and one plant, fewer people than Taishan employs.
Jiangsu Difeida Electronics
The Difeida name covers a 1997 PCB fab and a separate EMS company that carried NEEQ code 873105. Only one of them owns dfd338.com and the drill floor.
Jiangsu Hehong Electronics - Shanghai Hehong
Jiangsu Hehong's Dongtai base is quoted at 100,000 or 60,000 m2 a month, while its NEEQ-listed Shanghai parent reports 75.16% utilisation for 2025.
Jiangsu Xiehe Electronics
The same 2025 turnover appears as RMB 979 million in Chinese and USD 145 million in English; audited FY2024 was RMB 853.5 million on 1.15 million m2.
Jiangsu Yuantai Electronic Technology
Yuantai's 1.8 million m2 a year and RMB 1.5 billion sales are planned or full-production targets, not achieved output. First phase started in late 2023.
Jinhong Electronics (Ji'an)
Jinhong's own pages give three plant areas, three headcounts and four layer counts, and call the site both a quick-turn shop and a volume factory.
Jinkang Circuit Board (Yiyang)
Jinkang lists only Yiyang as a plant, yet quotes 120,000 m2 a month on its site, 100,000 in its EIA and a mixed FPC/HDI/rigid-flex total.
JOVEPCB (Zhongfu Circuit)
JOVEPCB describes three production bases in Chinese and five in English, and quotes 34 layers that turn out to be a prototype limit, not a production one.
Kaifa (Shenzhen Kaifa)
Kaifa's filing publishes its credit code, 150-plus SMT lines and a 15,000 m2 cleanroom. It is an EMS group, and its plant list depends on which page you read.
King Brother (KINGBROTHER)
Kingbrother books 100,000 PCB part numbers a year, while an older page on the same site implies 120,000. Neither figure is in square metres.
Kinwong
The 80-layer figure belongs to Kinwong high-layer-count line, not every plant. Seven bases, four product families, and one certificate you can verify.
Kunshan Huaxin Electronics Group
A private Kunshan group claiming 2.2 or 2.6 million m2 a year, 2,200 or 2,300 staff and three addresses. Its certificates are editions withdrawn before 2010.
Lidebao Electronics (Xiamen)
Lidebao publishes MCPCB specs down to the model, but its only UL file, E480769, covers a high-thermal adhesive film rather than a finished board.
Mankun Technology (Ji'an)
One Mankun page mixes a 2025 product mix of 22.22% with a Thailand design target of 67.27%, and states capacity that is a group total, not a Ji'an one.
Mektec Manufacturing (Zhuhai)
Zhuhai's flex plant is filed as wholly owned but registered 80/20, runs 1.25 million m2 of FPC a year, and publishes no process table.
Mingzhenghong Electronics (Yiyang)
The English page claims 410,000 m2 a month but its own items sum to 590,000; Shenzhen and Jiangmen are finishing plants under one Yiyang legal person.
Nan Ya PCB (Kunshan)
Nanya's Kunshan entity has 3,931 staff and USD 275.8m in capital, but its 2026 equipment filing says total output stays unchanged.
Ningbo Kehaoda Electronics
Kehaoda's one spec page quotes a 26:1 aspect ratio and 12 mil laser drills on a 4,500 m² site, while its 2024 environmental filing covers a single-sided line.
Ningbo Wakan Electronic Science & Technology
Wakan's domain is dead and its only first-party pages are two WeChat posts. The Kelvin test claims are auditable; the headcount and capacity are not.
Ningbo Zonbo Electrical
Zonbo claims 12,000 m² of PCB fabrication a month, yet its registered scope covers appliances and auto parts and every catalogue item is an assembled board.
Onpress PCB (Guangdong Anbai Circuit)
Onpress dates to 1987 in Hong Kong, 1992 as a relocation and 1993 as a PRC entity. Its published capacity uses four units that cannot be reconciled.
Q&D Circuits (Qiangda)
Q&D Circuits runs 50-layer builds and 10,000 part numbers a month from Shenzhen, but its own pages disagree on whether it employs 1,200 people or 1,350.
Redboard Technology (Ji'an)
Redboard's sharpest numbers come from two different documents: a 2026 IPO prospectus and a 2023 tax-bureau visit to one Ji'an site.
Reyhelm Electronics (Ji'an)
The Chinese site says 150 staff and 50,000 m2 a month; the English site says 300 staff and 30,000 m2, and neither version is marked as current.
S&L Circuits (Sunly PCB)
The same Shenzhen manufacturer appears as S&L Circuits, Sun&Lynn and Sunly PCB. Its certificate count differs by page, and its plants are split by board type.
Sandeguan Precision Circuit (Shenzhen)
Suntak holds 49% of Sandeguan and guaranteed part of a 2026 bank line for it. The FPC maker narrowed its loss but remains loss-making.
Sanlicheng Technology (Yiyang)
Sanlicheng moved its production from Huizhou to Yiyang, but 700,000 m2 a month is a website plan; a 2025 government note records four lines at 100,000.
Shanghai Jiajietong (Fast-PCB)
Jiajietong's Jiading address runs real etch lines - two plants plus a 2025 expansion - yet the same site prints four plant-area pairs and three age claims.
Shanghai Meadville Electronics (SME, AKM Meadville)
TTM sold Shanghai Meadville and substrate sister SMST to AKM Meadville for US$550m in 2020 - yet recruitment pages still describe SME as a TTM member.
Shengyi Electronics
Shengyi publishes certificate expiry dates per plant, which most Chinese factories do not. Its capability table merges five product families.
Shennan Circuits (SCC)
Shennan publishes one capability table for a group spanning five plants. Which column you quoted, sample or volume, decides whether the plant can build it.
Shenzhen Lianshuo Precision Electronics
Lianshuo's site claims a 2002 founding and 2003 certifications, but its registry date is 2012 and its own certificate page lists only ISO9001.
Sihui Fuji (FSQuality)
Fuji prints its UL file number in text, including the heavy-copper ratings most suppliers leave undefined. Its layer ceiling is stated three ways.
Stariver Circuit (Huangshi)
Three headcount figures for one plant, falling from 400 to 170, against an unchanged 120,000 m2 a month. Either the count is partial or the lines are quiet.
Sunshine Global Circuits
Sunshine quotes capability in standard and advanced columns, and its own pages disagree on layer count. German and Malaysian plants change delivery options.
Suntak Technology
Suntak publishes no capability table. Its layer and line figures exist only in annual-report prose, and substrate work sits in a partly owned subsidiary.
Tripod Electronics (Wuxi) - Tripod Technology
Tripod's Wuxi site is credited with 500,000 m2 a year of HDI, but that is one approved 2019 project, not the plant. Headcount reads 14,510 or nearly 20,000.
Unimicron Huangshi (Xinyixing)
Two names, two addresses and three investment figures attach to one Unimicron site. No certificate number has been published since output began in 2018.
Unitech PCB (Shanghai Zhanhua)
Production moved to Nantong in 2020 - the Qingpu address is an office. The English site serves a stripped test page; layer counts come from a TPCA directory.
Universal Scientific Industrial (Shanghai) (USI)
Zhangjiang assembles for a group that shipped 1.08 billion units in 2024, but USI fabricates no bare boards - it buys them. Ask fabrication elsewhere.
Victory Giant Technology
Victory Giant publishes layer counts and build-ups but no line, drill or panel table. Its HDI numbers also differ between the website and the IPO coverage.
Welgao Electronics (Ji'an)
Welgao's listed Jiangxi parent was formed in 2017, thirteen years after its Huizhou subsidiary that began the PCB business.
Worldex (Olympic Circuit)
Worldex publishes one capability grid for four families and supplies six named car makers. Its English site is also about a billion renminbi out of date.
WUS Printed Circuit
WUS publishes per-family maxima: 64 layers for backplanes, 40 for line cards, 34 for servers. Its 100-layer claim comes from an interview, not a document.
Xunjiexing (JXPCB)
Xunjiexing's site gives 2.8 million m2 a year, 2.6 million in an article, and 1.84 million when the four plants are added up one by one.
Yangzhou Elec & Eltek - Elec & Eltek / Kingboard
Yangzhou Elec & Eltek has four conflicting capacity figures spread across five or seven build phases, and only added HDI to the plant in 2025.
YCL (Inno Circuits)
Yingchuangli builds 2 to 48 layers in Suining and added IC and Mini-LED substrate lines in 2024. Its ChiNext application was withdrawn in 2022.
YD Electronic (Yidong)
The listing reads like an electronics company; the business is FPC, connectors and backlights. Rigid PCB is one new project that lost money in 2025.
Zecheng Electronics (Shenzhen)
The Shenzhen listed entity registers module and sensor production; FPC, HDI and SLP boards are made at its wholly owned Zhuhai subsidiary.
Zhaoqing Taihe Electronic
Taihe of Sihui was registered in 2016, but its UL and TS16949 record belongs to a 1992 Guangzhou predecessor. Three capacity figures disagree.
Zhuhai Access Semiconductor
Zhuhai Access builds IC substrates from 1.5 to 20 layers, converted to a joint stock company in 2012, with two shareholders telling different stories.