PCBA and EMS

PCB Repair and Rework in China

Replacing components, repairing traces and reballing area arrays under IPC-7711 and IPC-7721. The standard, the preheat and the record decide whether the board survives.

PCB Repair and Rework: recorded factories

Ordered by evidence strength, then by most recent review. Each profile states what was checked, on what date, and which processes are subcontracted rather than performed on site. A listing is not a guarantee of factory ownership or certification validity.

What this service covers

Repair and rework covers everything between a board that fails and a board that ships: component replacement, trace and pad repair, reballing, and correction of assembly defects.

IPC-7711 and IPC-7721 define the procedures and the acceptance criteria for rework and repair of electronic assemblies. A supplier that works to those standards can tell you what it did, how it verified the result and when a board should have been scrapped instead.

What decides whether the board survives

  • Preheat, not just top-side heat. Area-array packages need bottom-side preheat to bring the whole assembly near soldering temperature before the top-side nozzle acts. Without it, the local thermal gradient warps the board and can damage neighbouring joints.
  • Thermal profile matched to the assembly. A rework profile is developed per board thickness, package and neighbouring component density, not reused from the last job.
  • Moisture control. Boards that have absorbed moisture need baking before any reflow operation, or the vapour pressure causes delamination and popcorning.
  • Number of rework cycles. Each cycle degrades the pad and the laminate. After a defined number, the board should be scrapped regardless of whether it passes test.
  • Verification after rework. X-ray for area arrays, cross-section on a sample, and functional test. A reworked board that is only visually inspected is an unverified board.

What drives the price

  • Package type, with area-array and fine-pitch parts requiring dedicated equipment and longer cycle times.
  • Board value, which should decide how much rework is justified; a low-cost board is often cheaper to scrap than to repair.
  • Trace and pad repair, which is manual, microscope work and priced per repair.
  • Quantity, since setup dominates small batches.
  • Cleaning and recoating, which may follow rework if the board was coated.

What we check before listing a factory here

  • The factory states which standard it works to, and it is IPC-7711 and IPC-7721 rather than an internal procedure with no external reference.
  • BGA rework equipment includes bottom-side preheat and optical alignment, not only a hot air station.
  • A bake step is defined for boards that have been in storage or in the field.
  • Rework records are kept per board, with the operation, the operator and the verification result.
  • A scrap criterion exists and is applied, rather than every board being repairable until it passes.
  • Verification after rework includes X-ray or cross-section for hidden joints.

Where it goes wrong

  • Top-side heat only. The board warps, adjacent joints crack, and the failure appears at final test on a different component.
  • No bake before rework. Delamination shows as a blister under the package, and the cause is invisible after the fact.
  • Unlimited rework cycles. The same board is reworked four times, passes test, and fails in the field at the pad that was never designed for it.
  • Rework without verification. The replacement part is on the board and the joint was never checked, because visual inspection cannot see it.
  • Repair used to rescue a design fault. A systematic failure is patched unit by unit instead of being fixed in the process.

How it differs from neighbouring services

Assembly builds the board; rework corrects it. Testing verifies both, and is the input to a rework decision. A factory that offers rework without a stated scrap criterion is offering to keep working until the board passes, which is not the same as repairing it.

What to send in an RFQ

The failure description with quantity and failure rate, the board and stack-up, whether the board has been powered or in the field, the package types involved, and the verification you require. The repair quote specification lists the fields that change the price.

If the failure rate is systematic rather than random, read how we verify and treat it as a process question, not a repair order.