PCBA and EMS

PCB Design Services in China

Schematic capture, stack-up, layout and manufacturing outputs. The deliverable that matters is not a Gerber file; it is a design the chosen factory can build at the quoted yield.

PCB Design Services: recorded factories

Ordered by evidence strength, then by most recent review. Each profile states what was checked, on what date, and which processes are subcontracted rather than performed on site. A listing is not a guarantee of factory ownership or certification validity.

SEIC (Shenzhen Shinelong Electronics)

深圳先隆电子实业有限公司

SEIC pages say 75, 400 or 500 staff and put the plant at 1,800 or 12,000 square metres. A buyer's question list built from the differences.

Shenzhen

Founded 1997 · Evidence: Public sources reviewed · Reviewed 2026-11-19

View factory profile

Cixi Qingbao Electronic Technology

慈溪市清宝电子科技有限公司

Cixi Qingbao publishes 3 mil line/space; a 2026 Ningbo government article says 0.15 mm. Both are in print, neither is dated, and output figures differ too.

Ningbo rigidmultilayer

Founded 2017 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

Fastprint (Xingsen)

深圳市兴森快捷电路科技股份有限公司

Fastprint is a brand over several legal entities. The prototype business, the substrate business and a cancelled expansion tell three different stories.

Shenzhen multilayerhdi

Founded 1993 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

JCD (Jingchengda)

深圳市精诚达电路科技股份有限公司

Jingchengda's Chinese profile claims 2,000 staff and two plants; its English page says 860 staff and one plant, fewer people than Taishan employs.

Shenzhen flexiblerigid flex

Founded 2003 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

JOVEPCB (Zhongfu Circuit)

深圳中富电路股份有限公司

JOVEPCB describes three production bases in Chinese and five in English, and quotes 34 layers that turn out to be a prototype limit, not a production one.

Shenzhen rigidmultilayer

Founded 2004 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

King Brother (KINGBROTHER)

深圳市金百泽电子科技股份有限公司

Kingbrother books 100,000 PCB part numbers a year, while an older page on the same site implies 120,000. Neither figure is in square metres.

Shenzhen rigidmultilayer

Founded 1997 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

Putian Technology PCB (formerly GCI Jiesai)

中电科普天科技股份有限公司

Putian Technology is a CETC-controlled listed group whose PCB arm runs two named bases. Its 88-layer claim sits beside a 40-layer design limit.

Guangdong rigidmultilayer

Founded 2000 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

Shanghai Jiajietong (Fast-PCB)

上海嘉捷通电路科技股份有限公司

Jiajietong's Jiading address runs real etch lines - two plants plus a 2025 expansion - yet the same site prints four plant-area pairs and three age claims.

Shanghai rigidmultilayer

Founded 2004 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

Shenzhen Lianshuo Precision Electronics

深圳市联硕精密电子有限公司

Lianshuo's site claims a 2002 founding and 2003 certifications, but its registry date is 2012 and its own certificate page lists only ISO9001.

Shenzhen rigidmultilayer

Founded 2012 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

YCL (Inno Circuits)

四川英创力电子科技股份有限公司

Yingchuangli builds 2 to 48 layers in Suining and added IC and Mini-LED substrate lines in 2024. Its ChiNext application was withdrawn in 2022.

Sichuan multilayerhdi

Founded 2011 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

What this service covers

PCB design services cover schematic capture, stack-up definition, layout, design-rule checking and the manufacturing outputs: Gerbers, drill file, fabrication drawing, assembly drawings and usually a bill of materials.

Most design work in China is done by design houses that do not fabricate, and most fabricators do not design. That separation is normal and it is also where most of the risk lives, because a design rule set that is correct in the abstract may be impossible on the line that will build the board.

What decides whether the design is buildable

  • The design rules come from the factory, not from a template. Minimum trace, minimum gap, minimum annular ring and minimum drill are per-factory numbers tied to specific equipment. A design checked against generic rules can still fail at the chosen supplier.
  • Stack-up is a manufacturing document. Layer count, laminate per layer, prepreg type, copper weight and overall thickness with tolerance. Without it, the fabricator chooses, and the impedance you calculated is not the impedance you get.
  • Impedance is calculated against a stack-up, then measured. A target value without a stack-up and a test coupon is a wish. Controlled-impedance boards need a coupon on the panel.
  • Panelisation is a design decision. Board outline, rails, fiducials, tooling holes and the direction of the weave all affect yield and therefore price.
  • The output set is defined. Gerber alone is not enough for assembly; the centroid file, BOM with manufacturer part numbers and assembly drawing with polarity are separate deliverables.

What drives the price

  • Pin count and net count, which set layout hours more reliably than board area.
  • Layer count and stack-up complexity, especially controlled impedance and blind or buried vias.
  • Design iterations, which should be priced per revision rather than promised as unlimited.
  • Signal-integrity or thermal simulation, which is a separate engineering task.
  • Library and footprint creation, which is where hidden hours accumulate if the parts are unusual.

What we check before listing a factory here

  • The design house states which fabrication partners it designs for, and whether it checks rules against a specific factory’s capability.
  • Stack-up and impedance calculations are delivered as documents, not as verbal confirmation.
  • The output package is enumerated in the contract, including whether source files are delivered.
  • Ownership of the design files and the right to reuse libraries are stated in writing.
  • Revision control exists: each layout revision has a number, a date and a change note.
  • The design house can name the fabricators it has taken boards into production with, not only the boards it has designed.

Where it goes wrong

  • Design rules from a generic template. The board is manufacturable somewhere, and not at the factory that quoted it.
  • Impedance target with no stack-up. The fabricator substitutes an equivalent laminate, and the trace geometry no longer produces the target value.
  • Gerber-only handover. Assembly quotes come back inconsistent because every supplier is interpreting a different centroid and BOM.
  • Source files withheld. The client receives manufacturing data but cannot modify the design, so the next revision starts from zero.
  • Design and fabrication quoted as one price by different companies. The design house takes no responsibility for yield, and the fabricator takes no responsibility for the design.

How it differs from neighbouring services

Reverse engineering starts from a physical board and produces a design; this service starts from a specification. Fabrication turns the design into a board, and assembly places components on it. A design house that also assembles has an advantage in feedback, and a conflict of interest in quoting both.

What to send in an RFQ

A functional specification, the interface and connector list, mechanical constraints and enclosure drawing, target stack-up or an existing one, EMC and impedance requirements, the intended factory if known, and the deliverables you expect. The design quote specification lists the fields that change the answer.

If the board already exists and you need a design from it, read reverse engineering first, because the legal position is different.