PCB Cutting and Profiling in China
Separating boards from the panel: V-scoring, routing, breakaway tabs or laser. The method decides edge quality, tolerance and how the board behaves when it is separated.
PCB Cutting and Profiling: recorded factories
Ordered by evidence strength, then by most recent review. Each profile states what was checked, on what date, and which processes are subcontracted rather than performed on site. A listing is not a guarantee of factory ownership or certification validity.
Dongguan Lianqiao Electronics (L-Bridge)
A 16,000 m2 appliance-board plant that publishes real dimensions for four boards and dates for four of its five certificates. The fifth is contested.
Huizhou Glorysky Electronics
Glorysky's process table runs three year columns: 32 layers now, 36 in 2027 and 78 in 2028. Directories quote the last column as if it were today.
Ningbo Dongya Circuit Board (Beilun)
Dongya's dypcb.com lands on a domain-parking page and nbdypcb.com returns 502, so every Beilun capacity figure comes from a parent site or a directory card.
Ningbo Kehaoda Electronics
Kehaoda's one spec page quotes a 26:1 aspect ratio and 12 mil laser drills on a 4,500 m² site, while its 2024 environmental filing covers a single-sided line.
What this service covers
Cutting and profiling separate individual boards from the production panel. Four methods are common and they produce different edges:
- V-scoring cuts a V-shaped groove on both faces, leaving a thin web that is snapped after assembly. Fast and cheap, but it only works on straight lines across the full panel and leaves a visible groove.
- Routing mills the outline with a small cutter. It handles curves, internal cut-outs and connectors that overhang the edge, at a slower rate per metre.
- Tab routing with perforations, sometimes called breakaway tabs, leaves small tabs that are broken by hand. Useful for irregular shapes and for boards that cannot take the stress of snapping a V-score.
- Laser profiling cuts thin and brittle materials, and ceramic or metal-core boards, where mechanical stress is unacceptable.
Which method is used changes the mechanical stress on every component near the edge, so it is a design decision as much as a process choice.
What decides whether the outline can be cut as drawn
- Minimum internal radius. A router cutter has a diameter, so an internal corner can never be sharper than the cutter radius. A drawing with a zero-radius internal corner will be built with a radius whether the design says so or not.
- Distance from copper to edge. Routing and V-scoring both need clearance. Copper closer than the specified distance to the profile is exposed after cutting, and the board fails a visual inspection it would otherwise pass.
- Panel utilisation and rail width. Rails carry the panel through assembly equipment. Narrow rails save material and increase handling failures.
- Depanelisation method at the customer. A V-score designed for hand snapping and a tab designed for a depaneliser are not interchangeable, and the choice belongs to whoever separates the boards.
- Edge finish. Burrs, carbonisation from laser cutting and frayed edges on flex materials each need a different acceptance criterion.
What drives the price
- Outline length, since routing is priced per metre of cut.
- Number of internal cut-outs and slots, each of which is a separate tool path.
- Method, with V-scoring usually cheapest for straight lines and laser the most expensive.
- Panel count and rail strategy, which set how much material is used to deliver each board.
- Tolerance, because a tighter profile tolerance means slower feed rates and more inspection.
What we check before listing a factory here
- The factory states which profiling methods it runs on site, and which are subcontracted.
- Minimum internal radius and copper-to-edge clearance are published per product series, not only in a sales deck.
- Profile tolerance is stated as a number with the measurement method.
- Depanelisation stress is discussed for boards with components near the edge, since this is a common source of latent cracks.
- Laser profiling is offered only where it makes sense, which tells you whether the capability list is real.
- The factory can produce a first-article profile measurement for a new outline.
Where it goes wrong
- Internal corners drawn at zero radius. The board arrives with a radius, and the connector no longer seats.
- Copper too close to the profile. The edge is cut, the copper is exposed, and the board fails at final inspection after every other step has been paid for.
- V-score depth inconsistent across the panel. Some boards snap cleanly, others tear and delaminate.
- Tabs too strong or too weak. Strong tabs crack components during separation; weak tabs fail in handling before the customer ever sees the board.
- Rails sized for fabrication and not for assembly. The panel fits the router and not the placement machine.
How it differs from neighbouring services
Drilling establishes holes and layer registration; profiling establishes the outline. Both are mechanical steps that can damage the board, and both are usually quoted with fabrication rather than separately, which is why the method is worth stating explicitly in the RFQ.
What to send in an RFQ
The board outline with tolerances, internal cut-outs, the panel drawing with rails and fiducials, the intended depanelisation method, and the component keep-out near the edge. The cutting quote specification lists the fields that change the price.
If the board is rigid-flex or flexible, read flexible PCB first, because profiling a flex circuit has different constraints from cutting FR-4.