PCBA and EMS

SMT Stencil in China

A laser-cut or electroformed foil tensioned on a frame. Aperture area ratio, thickness and tension decide paste release, and a wrong stencil looks exactly like a good one.

SMT Stencil: recorded factories

Ordered by evidence strength, then by most recent review. Each profile states what was checked, on what date, and which processes are subcontracted rather than performed on site. A listing is not a guarantee of factory ownership or certification validity.

JLC (JLCPCB)

深圳嘉立创科技集团股份有限公司

JLC quotes in 24 hours and publishes a complete table. Its UL file is held by another entity, and no page says which of five plants runs your order.

Shenzhen multilayerhdi

Founded 2006 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

Shanghai Jiajietong (Fast-PCB)

上海嘉捷通电路科技股份有限公司

Jiajietong's Jiading address runs real etch lines - two plants plus a 2025 expansion - yet the same site prints four plant-area pairs and three age claims.

Shanghai rigidmultilayer

Founded 2004 · Evidence: Public sources reviewed · Reviewed 2026-11-11

View factory profile

What this service covers

A stencil is the tool that deposits solder paste on the pads. It is made from a metal foil with apertures cut to match the pad pattern, tensioned on a frame and used repeatedly.

Three manufacturing methods are in use:

  • Laser cutting is the default. A fibre laser cuts apertures from stainless foil, with the cut quality depending on the machine and the foil thickness.
  • Electroforming builds the foil by plating nickel onto a mandrel, producing smoother aperture walls and better paste release for fine pitch. It costs more and takes longer.
  • Chemical etching is the cheapest and is now mostly limited to coarse work, because the etched wall is not straight.

The stencil is designed alongside the paste process, so it should be ordered with the assembly, not afterwards from a catalogue.

What decides whether paste releases properly

  • Area ratio and aspect ratio. IPC-7525 defines the two ratios that predict paste release. Below the accepted thresholds, paste sticks in the aperture and the pad is starved, regardless of how well the stencil was cut.
  • Foil thickness. Thickness sets the paste volume. A thick foil helps through-hole and connector pads and over-deposits fine-pitch pads. Mixed boards need a stepped stencil or a compromise that is wrong for one of the two.
  • Aperture shape and wall angle. A trapezoidal aperture releases better than a straight wall. Laser cut quality and post-processing decide the wall angle.
  • Tension. A stencil that has lost tension will not stay registered across the print stroke, and the drift appears as random misalignment.
  • Nano coating. A hydrophobic coating improves paste release on fine apertures and extends cleaning intervals, which matters at volume.

What drives the price

  • Frame size and foil thickness, which are standard options rather than custom work.
  • Aperture count and minimum aperture size, since fine apertures need slower cutting and post-processing.
  • Method, with laser cheapest and electroformed the most expensive.
  • Step or cavity stencils, which need additional machining.
  • Turnaround, because stencils are usually on the critical path for a first build.

What we check before listing a factory here

  • The stencil supplier works to IPC-7525 for aperture design, and states the area ratio limits it applies.
  • Foil thickness is recommended per assembly rather than taken from the last job.
  • Aperture design is reviewed against the paste type and the component mix, not copied directly from the pad layer.
  • Tension is measured and stated, and the frame type is identified.
  • Nano coating or another release treatment is offered and its effect on cleaning interval is explained.
  • The supplier can produce a stepped stencil when a board mixes fine pitch with through-hole, rather than recommending one thickness for both.

Where it goes wrong

  • Aperture copied directly from the pad. The pad is designed for copper, not for paste, and the ratio falls below the release threshold.
  • One thickness for a mixed board. Fine-pitch pads get too much paste and bridge; connector pads get too little and starve.
  • Tension not checked. Registration drifts mid-print and the defect looks like a printer problem.
  • Electroformed stencil used as a default. It solves a release problem that may not exist, at a cost and lead time that does.
  • No cleaning schedule. Paste dries in the apertures and the stencil becomes a random defect generator.

How it differs from neighbouring services

The stencil is a tooling input to SMT assembly, not a service performed on the board. Fabrication produces the pads; the stencil decides how much paste lands on them. A stencil problem is almost always diagnosed as a printer or paste problem first, which is why the aperture design should be documented.

What to send in an RFQ

The paste-layer Gerber, the board thickness and panel size, the component mix with the finest pitch, the paste type, the frame size your printer accepts, and the quantity of stencils. The stencil quote specification lists the fields that change the price.

If the assembly is fine-pitch or area-array, read SMT assembly before ordering; the stencil decision and the paste process are one decision, not two.