PCB quotes

PCB Stencil Quotes: Area Ratio and Cut Quality

A stencil is cheap until the apertures get small. Price moves with the cutting method and with post-processing: laser cut with electropolish and a nano coating is a different product from a raw laser cut, and the difference shows up as paste release at fine pitch.

Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.

Main cost driver
Frame type, cut quality and area ratio of the smallest aperture
Typical lead time
1–2 working days

ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.

What this quote is priced on

Five to seven variables move the number on a stencil quote. They are not equally important, and only the first two are usually discussed.

  • Cut method. Laser cutting is standard. Chemical etching is cheaper for large features and less accurate at fine pitch, and the choice is decided by your smallest aperture.
  • Post-cut treatment. Electropolish smooths the aperture walls; nano coating lowers surface energy. Both improve paste release, and both are optional line items.
  • Frame. A framed stencil needs tensioning and a frame, which costs more to ship and releases more evenly. Frameless is cheaper and depends on the printer.
  • Thickness and stepping. Mixed paste requirements need a stepped or a two-piece stencil. The step is a machining operation, not a specification line.
  • Aperture count and area ratio. Very small apertures need narrower cut tolerance and more inspection. Density of fine apertures raises the price more than the total count.

The parameters a factory needs

This is the set that has to be in the enquiry before a stencil price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.

Stencil RFQ parameter set. State every row, or accept the factory's default.
Parameter What to state Why it changes the answer
Paste layer Gerber The paste mask layer, not the copper or the solder mask layer Apertures come from the paste layer. Cutting from copper wrong-sizes every mask-defined pad.
Smallest aperture and area ratio The smallest opening, its pad size and the resulting area ratio Below roughly 0.66 area ratio paste release becomes unreliable. The ratio decides the process, not just the price.
Frame type and size Framed with the frame dimensions, or frameless with the printer model The frame has to fit your printer. Supplying the printer model prevents a stencil that cannot be tensioned.
Foil thickness Thickness in micrometres, and any step regions with their depths Paste volume is thickness times aperture. One thickness for a board with mixed requirements starves or floods one side.
Cut method and post-treatment Laser or etched, with electropolish and nano coating yes or no These are the options that decide paste release at fine pitch, and they are priced separately.
Aperture count and finest feature Total aperture count and the finest feature dimension on the paste layer Cut time and inspection scale with aperture density, and the finest feature sets the achievable tolerance.
Quantity and repeat need How many stencils, and whether the design will be re-run Stencils wear and get damaged. Ordering a spare with the first one is cheaper than a second setup later.
Printer and squeegee constraints Printer model, squeegee type and any tension requirement Stencil and printer are a system. A stencil that does not tension correctly prints unevenly regardless of cut quality.

Send with the enquiry

  1. The paste-layer Gerber, plus the board thickness and panel size for framing.
  2. The smallest aperture on the paste layer, and the area ratio if you have calculated it.
  3. Frame type and size, or the printer model if you are unsure.
  4. Foil thickness, and a drawing of any step regions.
  5. Whether electropolish and nano coating are required, and how many stencils.

Where it goes wrong

  • Stencil cut from the copper layer. Every mask-defined pad gets the wrong aperture. The defect looks like a paste problem and is actually a data problem.
  • Area ratio below the working limit. Paste does not release from the aperture. At fine pitch this shows as random missing paste, which is often misdiagnosed as a printer fault.
  • One thickness on a mixed board. Power pads need more paste and fine pitch needs less. A single foil cannot do both, and the compromise fails both ends.
  • Frameless stencil for a printer that needs tension. The stencil cannot be mounted correctly, and print quality varies across the panel for reasons nobody can find.

Comparing two stencil quotes

Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.

  • Compare the post-treatment, not just the cut. Raw laser and polished with coating are different products.
  • Compare the frame and its dimensions. A cheap stencil that does not fit the printer is not cheap.
  • Compare the achievable cut tolerance at your smallest aperture.
  • Compare delivery time. Stencils are consumables, and a two-day delay stops a build that is otherwise ready.

What this page does not tell you

This page gives no area ratio formula values as a recommendation, because the working limit depends on your paste, your printer and your aperture shape. We describe the constraint; the number has to come from your process.

Related

Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.