SMT Assembly Quotes: Fine Pitch Sets the Price
Two boards with the same placement count can differ in price by a factor of two if one carries 0.4 mm pitch QFNs and BGAs. That content drives the stencil specification, the placement accuracy class and the inspection method, and all three are cost items.
Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.
ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.
What this quote is priced on
Five to seven variables move the number on a smt assembly quote. They are not equally important, and only the first two are usually discussed.
- Finest pitch. Pitch sets the stencil aperture, the paste type and the placement accuracy required. Below roughly 0.5 mm the process changes rather than tightens.
- BGA and bottom-terminated components. These cannot be inspected visually. X-ray is a separate machine and a separate line item, and skipping it removes the only check that works.
- Component mix. Connectors, shields, press-fit parts and large electrolytics often need hand placement or a selective process, which is a second pass.
- Stencil specification. Laser cut with electropolish and nano coating releases paste better at fine pitch. The stencil is a consumable priced into the run.
- Line changeover. Each unique part is a feeder and a verification. A short run with many line items spends most of its time in setup, not in placement.
The parameters a factory needs
This is the set that has to be in the enquiry before a smt assembly price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.
| Parameter | What to state | Why it changes the answer |
|---|---|---|
| Finest pitch and smallest package | The smallest pitch and the smallest body on the board, with package types | This single pair of numbers sets the stencil, the placement class and the inspection method. |
| BGA and LGA count | How many area-array parts, their pitch, and whether X-ray is required | Area-array joints are invisible. The count decides whether X-ray is a line item or an afterthought. |
| Mixed-technology content | Through-hole connectors, press-fit parts, shields and any hand-soldered items | Mixed boards need a second operation, a pallet or selective soldering, which is priced separately from SMT. |
| Stencil requirement | Thickness, step regions and whether a nano coating is required | Mixed paste heights need a step stencil. A single-thickness stencil cannot deposit two volumes correctly. |
| Placement accuracy class | Whether the board needs standard or high-accuracy placement, and why | High-accuracy placement is a different machine and a different rate, and it is only justified by the finest part. |
| Reflow profile constraint | Peak temperature and any restriction from a temperature-sensitive part | One sensitive part can force a lower peak, which constrains paste choice and every other joint on the board. |
| Panel design for the line | Panel size, rails, fiducials and whether the array is already defined | The line handles panels. A missing fiducial or rail means the factory adds one, and charges for the panel work. |
| First-article requirement | Whether FAIR is required, and to which standard | First-article inspection is a real cost and a real schedule item. Assuming it is included is a common misunderstanding. |
Send with the enquiry
- Gerber, centroid and the assembly drawing with polarity and reference designators.
- The finest pitch and the smallest package on the board.
- BGA count with pitch, and whether X-ray inspection is required.
- The stencil thickness you need, and any step regions for mixed paste heights.
- The IPC-A-610 class you will accept, and whether first-article inspection is required.
Where it goes wrong
- No X-ray on BGAs. It removes the only inspection that can see the failure mode BGAs actually have. The boards ship and fail in the field.
- Single-thickness stencil on a mixed board. One region gets too much paste and the other too little. The defect rate is blamed on the printer and is actually the stencil.
- Reflow peak chosen for the largest part. A temperature-sensitive component elsewhere on the board is cooked. The constraint has to be declared, not discovered.
- Panel without fiducials. The machine cannot register globally. The factory adds fiducials, charges for the panel work, and the schedule moves.
Comparing two smt assembly quotes
Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.
- Compare the finest pitch each supplier assumed. It is the number that drives most of the price difference.
- Compare whether X-ray is included and on how many parts.
- Compare the inspection standard: IPC-A-610 Class 2 and Class 3 are different acceptance criteria.
- Compare panelisation assumptions. Panel work is sometimes quoted separately and sometimes buried.
What this page does not tell you
This page does not state a minimum pitch capability, because it depends on the package, the stencil and the machine together, and factories that quote the number rarely measure it on your part.
Related
- SMT assembly: stencil, placement and reflow in sequence
- Stencil quotes: area ratio and cut quality
- Testing quotes: AOI, X-ray and functional coverage
- Assembly quotes: the wider package
Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.