PCB Repair Quotes: The Method Is the Answer
Repair is priced on the operation, not on the board. Replacing a connector is minutes; replacing a BGA under a shield can is an hour of controlled heating and a reball. The quote should name the method — hot air, infrared, laser or hand soldering — because the method is what determines whether the part survives.
Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.
ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.
What this quote is priced on
Five to seven variables move the number on a repair and rework quote. They are not equally important, and only the first two are usually discussed.
- Access. A part under a shield, on a thick board, or next to a connector takes longer to reach than its replacement takes to perform.
- Package type. Two-terminal passives are trivial. Area-array packages need preheat, profile control and often a reball, and the joint quality is invisible without X-ray.
- Method and equipment. Hot air, infrared, laser and hand soldering are priced differently and produce different thermal profiles. The method is the quality variable.
- Board thermal mass. A heavy-copper or metal-backed board needs more heat and a longer soak. Thin boards need support to avoid warp.
- Verification. Retest, X-ray and functional check are separate steps. A repair without verification is an attempt, not a repair.
The parameters a factory needs
This is the set that has to be in the enquiry before a repair and rework price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.
| Parameter | What to state | Why it changes the answer |
|---|---|---|
| Failure description and rate | What fails, how many boards, and whether the failure is systematic or random | A systematic failure is usually a design or process issue. Repairing units without saying so means the cause stays in production. |
| Board and stack-up | Layer count, thickness, copper weight and base material | Thermal mass decides dwell time and preheat. Metal-backed and heavy-copper boards need a different profile entirely. |
| Package type and location | Package, pin count, pitch, and whether the part is under a shield or beside a connector | Access is often the largest labour item. Location decides whether the repair is minutes or an hour. |
| Permitted rework method | Hot air, infrared, laser, hand soldering, or whatever is qualified | The method sets the thermal profile and the risk to neighbouring parts. Leaving it open means the cheapest method is used. |
| Restore to specification or to function | Whether the board must meet the original specification or only work | These are different acceptance criteria. A functional fix may not survive qualification or warranty. |
| Replacement part source | Whether the part is supplied, consigned, or sourced by the repair house | Sourcing an obsolete part is a cost and a delay. It is not included unless stated. |
| Quantity and turnaround | Number of boards, and whether they are needed in a batch or individually | Batch repairs amortise setup and programming. Single units carry the whole setup. |
| Post-repair verification | Retest level, X-ray requirement, and who signs off | Verification is the only evidence the repair worked. Without it you have an invoice and an assumption. |
Send with the enquiry
- A photograph with the affected part marked, plus the board or a sample if it can ship.
- How many boards, and whether the failure is systematic.
- The package and its location relative to shields and connectors.
- The method you will accept, and the verification you require.
- Whether the repair must restore specification or only function.
Where it goes wrong
- Top-side heating only. The board warps and neighbouring joints crack. The repaired part works and the board fails somewhere else two weeks later.
- No scrapping criterion. Some boards cannot be repaired without destroying them. Without a rule, effort is spent on units that should have been scrapped.
- Repair without finding the cause. The same failure returns in the next batch. Repair treats the symptom; the parameter table is what surfaces the cause.
- Function accepted as specification. The board works and no longer meets its qualification. It fails in the field, and the repair is blamed rather than the criterion.
Comparing two repair and rework quotes
Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.
- Compare the stated method. Hot air and laser are not the same repair even when the price looks similar.
- Compare what verification is included. Retest and X-ray are separate line items.
- Compare the acceptance criterion: specification or function.
- Compare throughput assumptions. A price per board at batch volume is not a price for one unit.
What this page does not tell you
This page does not say whether a given board is repairable. That depends on the damage, the access and the thermal history, and the honest answer comes from inspecting the unit rather than from a price list.
Related
- Repair and rework: methods, preheat and scrap decisions
- Testing quotes: finding the failure before you repair it
- Assembly quotes: the process that produced the fault
- Coating quotes: why coating makes rework destructive
Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.