Conformal Coating Quotes: Masking Is the Cost
The coating material is a small part of the price. Masking is the cost: every connector, test point, adjustment and optical window has to be masked and later unmasked, and that is hand labour. Selective spraying reduces masking but needs a program and a fixture, and parylene is a vacuum process priced by chamber volume rather than by board.
Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.
ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.
What this quote is priced on
Five to seven variables move the number on a conformal coating quote. They are not equally important, and only the first two are usually discussed.
- Masking and unmasking. Hand labour per keep-out area per board. A board with twenty masked features costs more to coat than a board with two, regardless of size.
- Chemistry. Acrylic, urethane, silicone and parylene differ in price, in cure method and in how removable they are. Parylene is a vacuum deposition process with its own economics.
- Application method. Dip, spray, selective spray or vacuum deposition. Selective spraying cuts masking and needs a program and fixture, which is a one-off cost.
- Thickness control. A specified thickness with tolerance requires measurement and often a second pass. Thickness is a process parameter, not a coat-and-hope step.
- Cure and handling. UV cure is fast; moisture cure takes days. Cure time occupies racks and delays shipment, and some chemistries cannot be accelerated.
The parameters a factory needs
This is the set that has to be in the enquiry before a conformal coating price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.
| Parameter | What to state | Why it changes the answer |
|---|---|---|
| Coating chemistry | Acrylic, urethane, silicone or parylene, and the environment it must survive | Chemistry decides cure, thickness range and removability. A coating chosen for cost can make later rework destructive. |
| Required thickness and standard | Micrometres with tolerance, and the IPC-CC-830 class or your own spec | Thickness is measured, not assumed. A tolerance without a measurement method is not verifiable. |
| Keep-out drawing | Every connector, test point, adjustment, optical window and press-fit area, marked | Masking labour is priced from this drawing. A verbal description produces a guess and a dispute. |
| Application method | Dip, spray, selective spray or vacuum deposition, or the constraint that decides it | Selective spray needs a program and fixture. Choosing it after the quote adds tooling. |
| Board cleanliness before coating | Whether boards are cleaned, and to what ionic contamination limit | Coating over flux residue traps contamination and can cause corrosion under the film, which is worse than no coating. |
| Inspection method | UV tracer under UV light, thickness measurement, or both | Visual inspection cannot see coverage on a clear coat. UV tracer is the only practical check. |
| Rework access afterwards | Whether components may need replacing after coating, and how removal is expected | Silicone and parylene are difficult to remove. Rework after coating is either destructive or a separate process. |
| Test sequence | Whether coating happens before or after functional test | Coating before test seals in the fault. Test before coating is the cheaper order, and it has to be stated. |
Send with the enquiry
- The chemistry you need, and the environment the board will operate in.
- Thickness with tolerance, and the standard or class being applied.
- A keep-out drawing marking every masked feature.
- Whether boards are cleaned before coating, and the ionic limit.
- Whether coating comes before or after functional test, and whether rework is expected.
Where it goes wrong
- Coating before final test. The fault is sealed in and the board cannot be probed. The repair is now a coating removal job, which is more expensive than the board.
- Coating before rework is finished. Rework destroys the coating and the surrounding components. Silicone and parylene make this worse than acrylic.
- Keep-outs described instead of drawn. A masked connector that should have been open, or a coated test point that should have been masked. Both are discovered at test.
- Coverage verified visually. Clear coats look complete and are not. Without UV tracer or thickness measurement there is no evidence the coating exists where it matters.
Comparing two conformal coating quotes
Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.
- Compare the masking scope. It is the largest line and the easiest to understate.
- Compare the chemistry and its removability, not just the price per board.
- Compare whether thickness is measured and reported, or only applied.
- Compare the test sequence assumed. A quote that coats before test has priced a risk you are carrying.
What this page does not tell you
This page gives no thickness recommendations, because the right figure depends on the chemistry, the environment and the standard you are working to, and the standard itself offers ranges rather than single values.
Related
- Conformal coating: chemistry, masking and cure
- Repair quotes: what coating does to rework cost
- Testing quotes: test before the coat goes on
- Assembly quotes: where the wash decision is made
Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.