Factory profile · Public sources reviewed

Sunshine Global Circuits

深圳明阳电路科技股份有限公司 · Shenzhen, Guangdong · Founded 2001 · SZSE ChiNext 300739, listed 2018

Sunshine quotes capability in standard and advanced columns, and its own pages disagree on layer count. German and Malaysian plants change delivery options.

Sunshine fits a high-mix, low-volume programme that needs a mainland factory plus a European or Malaysian delivery option. It does not fit a buyer who wants one unambiguous capability number: the company publishes two columns, standard and advanced, and the layer ceiling differs by twenty-eight layers depending on which page you read.

Identity and record

Only entries that were checked against a source are shown. A blank field means we have not confirmed it, not that it does not exist.
Registered name (Chinese) 深圳明阳电路科技股份有限公司
Registered name (English) Sunshine Global Circuits Co., Ltd.
Founded 2001
Listed SZSE ChiNext 300739, listed 2018
Headquarters Shenzhen, Guangdong
Production sites Shenzhen (Bao'an) · Jiujiang (Jiangxi) · Remscheid (Germany) · Penang (Malaysia)
Official website https://en.sunshinepcb.com
Evidence levelPublic sources reviewed
Last reviewed2026-11-11
Registered entity and published production sites Registered entity Sunshine Global Circuits and 4 named production sites, from the disclosures cited on this page. PUBLISHED RECORD Sunshine Global Circuits 深圳明阳电路科技股份有限公司 Founded 2001 · SZSE ChiNext 300739, listed 2018 Shenzhen Bao'an Jiujiang Jiangxi Remscheid Germany Penang Malaysia Source: disclosures cited on this page
Entity and footprint map. Sunshine Global Circuits and the production sites named in the disclosures cited above.

Two columns, and a ceiling that moves

The process page is organised as standard and advanced, which is a more honest presentation than most: it separates what every line runs from what a qualified line runs when the design demands it. Aspect ratio goes from 20:1 to 25:1, impedance tolerance from ±10% to ±5%, HDI build-up from 3+N+3 to 7+N+7, board thickness from 6 mm to 8 mm.

Then the pages disagree. The branch-office page describes the Shenzhen facility as capable of 2 to 70 layers, while the process table tops out at 62 in the advanced column. The backplane row separately claims 60 and 70 layers. Two numbers, both published by the same company, neither reconciled. A buyer quoting a 68-layer backplane should not assume the answer is yes, and should not assume it is no: ask which line, and get the answer in writing with the stack-up attached.

The overseas plants are the real differentiator

Most mainland manufacturers compete on cost inside Guangdong or Jiangsu. Sunshine owns a plant in Remscheid, near Düsseldorf, acquired in 2013 and originally established in 1966, and a plant in Penang, Malaysia, that began operations in 1989 and was acquired in 2023 with about 2,500 m² per month across 2 to 16 layers.

That changes three things. A European delivery can be manufactured inside the EU, which matters for a customer who needs to avoid import duty or wants a shorter supply line for a repair loop. A Malaysian site gives a China-plus-one option without changing supplier. And the German plant, being a small high-mix operation, is the natural home for a 20-piece order that a Chinese volume line would decline.

The trade-off is price and process depth. A 2,500 m² per month plant cannot absorb a programme that scales, and the tooling and material costs of a European site are not Chinese costs. Ask which site is being quoted before comparing the number against a Shenzhen quote.

Jiujiang is where the volume sits

The Jiangxi base is the group’s scale answer: building 1 is 46,000 m², building 2 is 65,000 m² and is described as almost fully automated, with a dedicated line for substrate-like PCBs and Mini-LED work. If your order is tens of thousands of square metres, this is the site that matters, and the Shenzhen plant becomes a prototype and engineering resource.

The split also tells you how to phase a programme: qualify in Shenzhen or Germany on a small build, then transfer to Jiujiang, and insist that the transfer triggers a first-article inspection rather than being treated as the same process.

Why a high-mix buyer should care

A company that runs a 1966-vintage European plant, a Malaysian plant and two Chinese plants has had to build engineering-change machinery that a single-site factory never needs. That usually shows up as better documentation on multi-model orders, and as a more realistic attitude to minimum quantities. It also produces the situation in this profile: four sites, one group table, no per-site number.

What the record does not establish

There is no UL file number, so the UL listing has to be matched to the entity in UL Product iQ, and there is no per-plant capability split at all. The certificate list is a set of names without numbers, which means IATF 16949 and AS9100D cannot be tied to a specific site from public sources. AS9100D without a Nadcap special-process accreditation covers quality systems, not plating or chemical processing, so an aerospace programme should not read it as the full package.

One ownership note: the 2025 annual report identifies 丰县润佳玺企业管理有限公司 as controlling shareholder, a holding company that has been renamed more than once. That is not unusual for a ChiNext issuer, but a counterparty check should use the current registered name rather than the name on an older contract.

Published limits

Every value below is quoted as published by the company or a public record.

ParameterValue as published
Max layer count, standard / advanced 42 / 62 layers
Max board thickness, standard / advanced 6 mm / 8 mm
Outer-layer line width and spacing 3.5/3.5 mil / 3.0/3.5 mil
Inner-layer line width and spacing at 1 oz 2.8/2.8 mil / 2.5/2.5 mil
Aspect ratio, standard / advanced 20:1 / 25:1
HDI build-up, standard / advanced 3+N+3 / 7+N+7
Impedance tolerance on inner layer at 1 oz ±10% / ±5%
Max backplane layers, thickness, size 60 / 70 layers, 8 / 10 mm, 1200 × 680 mm
Min mechanical and laser drill, data-communication line 0.15 mm mechanical, laser 50–150 μm
Laminate grades listed S1000H, S1000-2M, IT-158, IT-180A, TU-865, EM827, 370HR, R-5775
Four layer ceilings across two board families Bar chart of 4 published figures in layers, standard and advanced limits on the capability sheet. The 42/62 pair covers multilayer boards and the 60/70 pair covers backplanes. Each pair is a standard and an advanced ceiling for one family; the four bars are not additive. ML standard 42 layers multilayer boards, standard ceiling ML advanced 62 layers multilayer boards, advanced ceiling BP standard 60 layers backplanes, standard ceiling BP advanced 70 layers backplanes, advanced ceiling
Four layer ceilings across two board families. layers, standard and advanced limits on the capability sheet. The 42/62 pair covers multilayer boards and the 60/70 pair covers backplanes. Each pair is a standard and an advanced ceiling for one family; the four bars are not additive. Source: published standard and advanced capability table.

Certifications on record

A certificate covers a legal entity and a site, not a brand. Scope and expiry are recorded where published.

StandardWhat the record shows
IATF 16949 Listed among systems certified; no certificate number or site scope published
ISO 9001 Listed among systems certified
ISO 13485 Listed among systems certified; useful for medical work only if the certificate names the site
AS9100D Listed among systems certified; no Nadcap special-process accreditation is mentioned
UL and CQC product safety Named as product-safety certifications; no UL file number published
ISO 14067 Product carbon footprint, listed on the same page

Ask this factory for a quote

Send one technical package and compare the replies. The RFQ checklist lists what to include; the quote specifications say which parameters change the price for the process you are buying.

Request a quote

Source and review conventions are described in how we verify. Corrections can be sent through the contact channel.