Q&D Circuits (Qiangda)
深圳市强达电路股份有限公司 · Shenzhen, Guangdong · Founded 2004 · SZSE ChiNext 301628 (2024-10-31)
Q&D Circuits runs 50-layer builds and 10,000 part numbers a month from Shenzhen, but its own pages disagree on whether it employs 1,200 people or 1,350.
A small-batch high-multilayer shop: 10 layers and up as the day job, 50 layers at the top, 10,000 part numbers shipped a month. Good for dense industrial and RF work in the tens to low thousands. Not a volume supplier, and its process limits are published only in a listing-day press piece, so ask for the stack-up history.
Identity and record
| Registered name (Chinese) | 深圳市强达电路股份有限公司 |
|---|---|
| Registered name (English) | Shenzhen Q&D Circuits Co., Ltd. |
| Founded | 2004 |
| Listed | SZSE ChiNext 301628 (2024-10-31) |
| Headquarters | Shenzhen, Guangdong |
| Production sites | Shenzhen · Ganzhou |
| Official website | https://www.qdcircuits.com/ |
| Evidence level | Public sources reviewed |
| Last reviewed | 2026-11-11 |
Ten thousand jobs a month, six square metres each
Q&D ships more than 10,000 part numbers a month and produces 800,000 m² a year. Divide one by the other and the average job is about 6.7 m² of finished board. For a shop whose stated main output is 10 layers and above, that is a remarkably small average.
The two numbers only fit together one way. This is a high-mix plant where a typical order is a handful of panels of a dense board, and where the fixed cost sits in engineering and test rather than in panel throughput. Six and a half square metres of 12-layer work is roughly a few dozen panels. Nobody sets up a line for that unless the whole plant is organised around changeovers.
That is the honest reading of “small batch, high-end”. It also tells you what to expect commercially: unit prices will be set per job, not per square metre, and any quote that looks like a volume quote has probably been built on an assumption you should check.
Twelve hundred people or thirteen fifty
The home page says 1,350-plus employees. The group profile and the English profile both say 1,200-plus, of which 400-plus are technical. The gap is 150 people, or about one eighth of the smaller figure.
One hundred and fifty is not a rounding error and it is not a second factory either. A three-shift crew on a single multilayer line, counting operators, inspection and maintenance, sits in the tens. So the difference between the two figures is on the order of one to three lines’ worth of people.
The Ganzhou plant page gives a third data point: 500-plus staff at the Jiangxi site, which leaves roughly 700 in Shenzhen if the 1,200 total is right. If the 1,350 is right, Shenzhen holds about 850. For a buyer, the practical consequence is that neither figure tells you how many lines exist. Ask for lines by type — mechanical drill, laser drill, vertical plating lines, AVI — rather than headcount, because lines are what a capacity commitment is made of.
Fifty layers at the top, ten and up as the day job
The published maximum is 50 layers, and the same page adds that Shenzhen mainly produces 10 layers and above. That combination is unusual among the Shenzhen shops on this site: most either run volume multilayer at 4 to 8 layers or chase one or two heroic builds. Q&D is organised around thick, dense, low-volume work as its base load.
No per-layer-band capacity is published. You cannot learn from the site how many 20-layer jobs a month the plant can absorb, nor where the crossover sits between Shenzhen and Ganzhou. The Ganzhou page describes small-batch multilayer without a layer range at all.
Twelve ounces is a certificate, thirty ounces is a quotation
Two copper numbers circulate and they are not the same kind of claim. The 12 oz figure is a UL certification statement — the company says it was the first in Asia to pass UL at that weight. The 30 oz figure comes from the listing-day coverage, alongside 2.0/2.0 mil inner-layer lines, 3.0/3.0 mil outer, 4.0 mil mechanical drill, 3.5 mil laser drill and a 20:1 maximum aspect ratio.
Nothing on the official site reconciles them, and the difference matters: a UL listing describes a construction that has been tested and may be marked, while 30 oz describes what the plant says it can build. Ask which layer count and which pattern the 30 oz was demonstrated on.
The capability page does not load, so the numbers come from the listing file
The site’s process-capability page renders empty in a browser without scripting, and the parameters above are therefore sourced from the 2024 listing coverage rather than from the manufacturer’s own table. That is not a scandal — plenty of Chinese factory sites are built this way — but it does mean the site cannot be used to verify a single process limit.
What the site does publish, precisely, is certification expiry. ISO 9001 runs to 2027-05-06, ISO 14001 to 2026-05-04, IATF 16949 to 2027-05-06. Dates without numbers are still worth more than numbers without dates: you know when to re-ask.
Seventy-seven gigahertz, in one sentence of one article
The 77 GHz automotive radar board is described in the listing coverage as leading in China. One sentence, no customer, no volume, no test data. High-frequency work is where this plant says it is differentiated, and it is also the area where a single sentence is least persuasive.
If radar or high-speed material is the reason you are looking at Q&D, ask for the laminate grades actually in use, the impedance coupon data from the last twelve months, and which insertion-loss measurements the plant performs in-house. The site will not answer any of those.
Nantong was about to open two years ago
The October 2024 listing coverage mentions a Nantong plant as about to start production. The current site carries no Nantong capacity, no start date and no output figure. Either the plant is running and unpublicised, or the plan changed. Do not assume a third site exists because a newspaper said so once.
What is not established
No unified social credit code, no exact headcount, no per-layer capacity, no certificate numbers, and no confirmation of the Nantong plant’s status. Customer names are absent, and the 5,000-plus customer figure in the profile conflicts with 7,500-plus on the home page. Neither number is dated.
Published limits
Every value below is quoted as published by the company or a public record.
| Parameter | Value as published |
|---|---|
| Maximum layer count | 50 layers |
| Main production layer range | 10 layers and above |
| Thick-copper UL certification | 12 oz, described by the company as an Asian first |
| Part numbers shipped | 10,000+ a month |
| Annual PCB output | 800,000 m2 a year |
| Annual model count | 150,000+ models |
| Combined plant building area | 50,000+ m2 |
| Headcount and technical staff | 1,200+ employees, 400+ technical |
Certifications on record
A certificate covers a legal entity and a site, not a brand. Scope and expiry are recorded where published.
| Standard | What the record shows |
|---|---|
| ISO 9001 | Valid to 2027-05-06 according to the certificate page; certificate number not published |
| ISO 14001 | Valid to 2026-05-04; no certificate number and no site list shown |
| IATF 16949 | Valid to 2027-05-06; the certified sites are not named, so Shenzhen and Ganzhou coverage is unclear |
| 12 oz thick-copper UL | Company states it was Asia's first 12 oz thick-copper PCB maker to pass UL; no UL file number disclosed |
| National little-giant | Certificate 202311071108, valid 2023-07-01 to 2026-06-30; a Chinese SME designation, not a product approval |
Ask this factory for a quote
Send one technical package and compare the replies. The RFQ checklist lists what to include; the quote specifications say which parameters change the price for the process you are buying.
Source and review conventions are described in how we verify. Corrections can be sent through the contact channel.