Metal-Based PCB Quotes: Dielectric Sets the Price
The base metal is a commodity; the dielectric is the product. Price moves with dielectric thickness and thermal resistance far more than with the aluminium thickness, and at low volume the punching tool dominates the entire quote.
Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.
ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.
What this quote is priced on
Five to seven variables move the number on a metal-based quote. They are not equally important, and only the first two are usually discussed.
- Dielectric thickness and thermal resistance. Thinner dielectric means lower thermal resistance and lower breakdown voltage. The two move in opposite directions, and the choice is an engineering decision priced as material.
- Base metal. Aluminium is the default. Copper spreads heat better and costs more; ceramic substrates are a different process entirely and are not a variant of the same quote.
- Outline method. Punching needs a hard tool per design, which is why it only makes sense at volume. Routing avoids tooling and leaves a burr that has to be controlled.
- Single-sided versus multilayer. Most metal-core boards are single-sided. Multilayer metal-core exists but is a specialist build, and asking for four layers is a good way to find out who read the enquiry.
- Thermal vias and isolation. Isolated thermal pads and plated holes through the dielectric add process steps. Each one reduces the thermal benefit you were buying the substrate for.
The parameters a factory needs
This is the set that has to be in the enquiry before a metal-based price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.
| Parameter | What to state | Why it changes the answer |
|---|---|---|
| Base metal | Aluminium, copper or ceramic, with the alloy or grade | Different processes, not different prices for the same thing. Ceramic in particular is not a variant of an aluminium quote. |
| Dielectric thickness and thermal resistance | A thickness in micrometres and the thermal resistance you need | These two are coupled. Stating one without the other lets the factory choose the trade-off for you. |
| Breakdown voltage and isolation | The isolation voltage, and whether any pads must be isolated from the base | Higher isolation needs thicker dielectric or an isolated island, both of which raise thermal resistance. |
| Thermal cycling requirement | Temperature swing and cycle count, if the part is power-cycled | Dielectric and base expand differently. Cycling requirements decide the material class, not just the thickness. |
| Outline method | Punched, routed or laser-cut, with the tolerance you will accept | Punching carries a tool charge that only amortises at volume. The method can change the price by more than the material. |
| Layer count | Single-sided or multilayer, and where the copper layers sit | Multilayer metal-core is a specialist build with few suppliers. Assuming it is routine delays the whole project. |
| Power density on the board | Watts dissipated per LED or per component, and the total | Thermal design follows this number. Without it, the dielectric is chosen by habit rather than by need. |
| Annual volume | Volume at launch and at steady state, and the tooling owner | Tooling amortisation is the largest single line at low volume, so volume decides whether punching is viable at all. |
Send with the enquiry
- The base metal and grade, and the application that requires it.
- Dielectric thickness plus the thermal resistance or the watts to dissipate.
- The isolation voltage and any pads that must be electrically isolated from the base.
- The outline method you expect, and the volume that would justify a punch tool.
- Whether the build is single-sided or multilayer, and who owns the tooling.
Where it goes wrong
- Quoting a four-layer metal-core board as routine. The format barely supports it and few plants do it. The reply tells you whether the supplier read the enquiry.
- Thicker aluminium assumed to cool better. Thermal performance is dominated by the dielectric and the copper foil. Aluminium thickness mostly adds stiffness and weight.
- Isolation added after the dielectric is chosen. Isolation and thermal resistance trade against each other. Deciding one first forces a compromise on the other after the design is frozen.
- Punch tooling paid twice. At low volume the tool can be most of the quote. If the tool is not yours, moving supplier means paying for it again.
Comparing two metal-based quotes
Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.
- Compare dielectric thickness and thermal resistance together. A quote that lists only one has not answered the thermal question.
- Check whether tooling is included, owned by you, and movable.
- Compare the outline method. Punched and routed parts have different edge quality and different tolerances.
- Ask whether the quoted build is single-sided. Multilayer metal-core quotes are frequently requoted once the factory reads the stack.
What this page does not tell you
This page gives no thermal resistance figures, because they depend on dielectric thickness and on the copper pattern above it. A single number per material is misleading without the layout it was measured on.
Related
- Metal-based boards: four material families compared
- Aluminium boards: the common case in detail
- Cutting and profiling: punch versus route
- Rigid quotes: the baseline this format replaces
Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.