PCB quotes

Rigid PCB Quotes: What to Send, What Sets Price

A rigid board is priced as a panel. The factory nests your outline into a standard panel size, and how many boards fit decides the material cost far more than the board area does. Two suppliers quoting the same Gerber can land a third apart because one of them found a better step-and-repeat, and neither number is wrong.

Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.

Main cost driver
Panel utilisation, thickness tolerance and surface finish
Typical lead time
3–7 working days for prototypes, 2–4 weeks for production

ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.

What this quote is priced on

Five to seven variables move the number on a rigid pcb quote. They are not equally important, and only the first two are usually discussed.

  • Panel utilisation. A 2 mm change in outline can take a board from twelve per panel to nine. That is a 25 %material change before any process cost, and it is invisible in a per-board price.
  • Thickness and its tolerance. 1.6 mm ±10 % and 1.6 mm ±0.1 mm are different products. The tight version constrains the press cycle, forces tighter prepreg build-up and raises scrap on both ends of the run.
  • Warp limit. IPC-6012 asks for 0.75 % on surface-mount boards. Stating it changes the press and the bake. A factory that ignores it ships boards flat enough to look right and too warped for your printer.
  • Copper weight. 1 oz outer layers are the default. 2 oz changes etch factor, plating time and the minimum trace width the plant can hold, so it moves the price through yield rather than through metal cost.
  • Surface finish. HASL, lead-free HASL, ENIG, OSP and hard gold run on different lines. ENIG costs more and buys flatness that matters at fine pitch; OSP costs least and loses shelf life.
  • Outline and edge. Routing and V-scoring are different processes, and the choice is set by how the board will be separated. V-score needs rail space in the array, which competes with panel utilisation.
  • Acceptance class. IPC-6012 Class 2 and Class 3 differ in annular ring, plating thickness and inspection sample size. A quote that does not name the class is quoting Class 2 and hoping you do not ask.

The parameters a factory needs

This is the set that has to be in the enquiry before a rigid pcb price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.

Rigid PCB RFQ parameter set. State every row, or accept the factory's default.
Parameter What to state Why it changes the answer
Board outline with tolerances Width, height, corner radii and every cut-out, dimensioned Panel nesting is calculated from this. A missing tolerance is silently read as the factory default, usually ±0.2 mm.
Finished thickness and tolerance For example 1.6 mm ±0.16 mm, and who owns the tolerance stack Thickness is built from prepreg and core, so the tolerance decides how many laminate combinations are allowed.
Warpage requirement IPC-6012 0.75 % or your own figure, and the measurement method Drives press cycle, bake and cooling. Boards quoted without it are held to the factory default, which is rarely 0.75 %.
Copper weight per layer Outer and inner layers stated separately, finished or base copper Base and finished copper are not the same number, and plating adds the difference. This is where a quote quietly becomes a different board.
Minimum hole and trace The smallest drill and the narrowest trace in the design Sets the process class. Below a certain combination the plant must slow the line, which is a price step, not a percentage.
Surface finish The finish you will assemble onto, with thickness where it matters Each finish has its own line and its own flatness. Choosing ENIG after quoting HASL changes the price and the lead time.
Solder mask and legend Colour, and whether legend is on both sides Mostly a lead-time item, but unusual colours are batch-produced and can force a wait for the next scheduled run.
Acceptance class IPC-6012 Class 2 or Class 3, and any customer-specific addendum Changes inspection, annular ring and plating thickness. Without it, the quote is for Class 2 by default.
Quantity and annual volume Per order, per release, and per year, stated as three numbers Setup and tooling amortise over the order. A quote for 50 boards says nothing about the price at 5,000.

Send with the enquiry

  1. Gerber files plus the drill file. A drawing alone cannot be fabricated.
  2. The stack-up with laminate named per layer and copper weight per layer.
  3. Board thickness with tolerance and the warpage limit you will inspect to.
  4. Quantity per order and expected annual volume, stated separately.
  5. The acceptance class, and whether you will audit to it or only ask for a certificate.

Where it goes wrong

  • Quotes without a stack-up. The supplier priced a layer count, not your board. The reply looks complete and is for a different dielectric build.
  • Comparing per-square-metre prices. Board shops quote panels. A per-area price ignores how much of the panel your outline wastes, which is often the largest single variable.
  • Asking for Class 3 as a courtesy. Class 3 changes annular ring and plating thickness, so a factory that agrees to it at the Class 2 price will either lose money or interpret it loosely.

Comparing two rigid pcb quotes

Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.

  • Hold the stack-up, the finish and the acceptance class fixed, then compare. A difference in any of the three is a different product, not a better price.
  • Ask each supplier to state boards per panel. Two prices that differ by 30 % usually differ in nesting, not in efficiency.
  • Compare the thickness tolerance, not just the nominal thickness. The tight one carries a real cost and a real benefit.
  • Check who supplies the laminate. Consigned material moves the risk to you and removes a margin from the price.

What this page does not tell you

This page cannot tell you what your board will cost, because the answer depends on the panel your outline nests into and on the queue that week. It also says nothing about whether a particular factory can hold 0.1 mm trace at production yield; that is a capability question, and the board-type pages are where we record it.

Related

Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.