Flexible PCB Quotes: Material Decides the Price
Flexible circuits are priced on film area, and handling loss is a larger share of the price than on rigid boards. PET costs materially less than polyimide and will not survive reflow, so the material is usually decided by your assembly process rather than by the circuit.
Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.
ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.
What this quote is priced on
Five to seven variables move the number on a flexible pcb quote. They are not equally important, and only the first two are usually discussed.
- Base film. Polyimide holds its properties through reflow and soldering; polyester does not. Choosing PET to save material cost moves the constraint into assembly, where it becomes a process problem.
- Copper thickness and type. Rolled annealed copper bends; electrodeposited copper is cheaper and cracks at tight radii. Thicker copper improves current capacity and shortens bend life.
- Layer count and shielding. Double-sided flex needs plated through holes in film, which is a different line from single-sided. Shielding adds a layer and a bonding step.
- Stiffeners and connector reinforcement. Every stiffener is a cut part and a bonding operation. Pressure-sensitive adhesive stiffeners are cheapest and least reliable under reflow.
- Panel yield and handling. Thin film distorts. Small parts on large panels lose yield to handling, and the loss is priced into every board whether or not you see it.
- Delivery format. Singulated, on tape, or in a panel for assembly. Tape-and-reel adds a carrier and a placement operation, but removes a manual step at your line.
The parameters a factory needs
This is the set that has to be in the enquiry before a flexible pcb price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.
| Parameter | What to state | Why it changes the answer |
|---|---|---|
| Base film material | Polyimide or polyester, with the maximum temperature the part will see | PET cannot survive reflow. If the part will be assembled on an SMT line, the material question is already answered. |
| Static or dynamic bend | Bend once at assembly, or flex continuously, with radius and cycles | Dynamic use constrains copper type, coverlay and layer count. It is the single biggest cost decision on a flex part. |
| Copper weight and type | Finished copper in micrometres, rolled annealed or electrodeposited | Sets current capacity and bend life together. Stating weight without type leaves the bend performance undefined. |
| Layer count and shielding | Single-sided, double-sided or multilayer, and whether an EMI shield is required | Double-sided flex requires plated holes through film, a separate process with its own minimums. |
| Stiffener locations | A drawing marking each stiffener, its material and thickness | Stiffeners set the height at connectors and the flatness under SMT parts. Missing them changes both the price and the fit. |
| Surface finish | ENIG, OSP, immersion tin or hard gold, with the reason | OSP on flex has a short shelf life and poor bend tolerance. Finish choice interacts with both assembly and bending. |
| Delivery format | Singulated, in a panel, or on tape and reel with the pocket size | Determines whether the factory adds a carrier. A format chosen after the quote adds a line item later. |
| Outline tolerance and registration | Outline tolerance, and whether the part locates on fiducials or on edges | Film moves during processing, so outline tolerance is looser than on rigid. Assembly fixtures have to be designed around it. |
Send with the enquiry
- Gerber plus the drill or punch file, and the outline with tolerance.
- The base film, the copper type and the finished copper weight.
- Whether the part bends once or continuously, with radius and cycle count.
- Stiffener drawing with material and thickness at every connector.
- The delivery format and, if taped, the pocket and pitch you need.
Where it goes wrong
- PET specified for a reflow assembly. The circuit works and the assembly destroys it. The failure appears as delamination around the first reflow, not at incoming inspection.
- No stiffener under a fine-pitch connector. The connector lifts under insertion force. The fix is a redesign, not a process change, and it usually appears after tooling is paid for.
- Bend radius stated as a number without a cycle count. Radius and cycles are one requirement, not two. A 1 mm radius that is formed once is a different part from the same radius in continuous motion.
- Assembly method left to the factory. A quote without it covers a part that cannot be placed on your line, and the discrepancy surfaces when the boards arrive.
Comparing two flexible pcb quotes
Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.
- Compare the film and copper type, not the layer count. Most of the spread between two flex quotes is material, not labour.
- Check whether stiffeners and tape are inside or outside the quoted price.
- Ask what panel each supplier is nesting into. Small parts on large panels carry a handling premium that is easy to hide.
- Compare the finish and its shelf life. A cheap OSP finish on a part stored for six months is not a saving.
What this page does not tell you
This page gives no bend-life numbers, because they depend on copper type, coverlay and radius in combination and are measured, not quoted. Any supplier who gives you a cycle count before seeing your geometry is guessing.
Related
- Flexible boards: materials, layer options and limits
- Rigid-flex quotes: when the board is both formats
- Stencils for flex: why the carrier matters
- SMT assembly: fixturing a flexible part
Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.