FR-4 PCB Quotes: Which Laminate Are You Buying?
FR-4 is a family of laminates, not a material. A generic quote assumes a standard Tg grade at 1.6 mm with 1 oz copper. If your design needs a 170 °C laminate, 2 oz inner layers or 0.8 mm finished thickness, that quote is for a board you are not building.
Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.
ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.
What this quote is priced on
Five to seven variables move the number on a fr-4 quote. They are not equally important, and only the first two are usually discussed.
- Laminate series. Within FR-4 there are standard, mid-Tg, high-Tg and halogen-free families, and the price step between them is real but modest next to the process consequences.
- Dielectric thickness per layer. Thin dielectric needs more prepreg plies and better press control. It also changes impedance, so the stack and the electrical target move together.
- Copper weight. Heavy copper etches differently, needs thicker resist and slows plating. Above 3 oz the minimum trace width grows and the price steps rather than slides.
- Colour and legend. Matte black and white masks cost more than green and are produced in batches, so they add waiting time more than unit cost.
- Material source. Branded laminate from a major supplier costs more than an equivalent domestic grade and is easier to audit. If your customer names a brand, that name is a price.
The parameters a factory needs
This is the set that has to be in the enquiry before a fr-4 price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.
| Parameter | What to state | Why it changes the answer |
|---|---|---|
| Laminate series or grade | The series name, or the Tg and Td you need if you have no preference | A brand or series is a price and a process. "FR-4" alone lets the factory pick whatever is in stock that week. |
| Tg and Td requirement | Tg value and the reason, plus Td if the board sees high temperature | Tg explains the reflow and operating envelope. Td covers decomposition, which matters for heavy copper and high layer counts. |
| Halogen-free requirement | Mandatory, preferred, or not required, and who imposes it | Halogen-free grades have different press windows and cost more. A preference stated as a requirement is money spent for nothing. |
| Dielectric thickness per layer | The target thickness for each dielectric, or the impedance that drives it | This is the stack-up. Without it the factory builds a standard stack that may not meet your impedance or your overall thickness. |
| Copper weight per layer | Base copper for inner layers, finished copper for outer layers | The two are quoted differently and plating adds the difference. Mixing them up produces a board that is thinner than specified. |
| Finished thickness | Nominal with tolerance, and whether it is measured over copper or laminate | Two measurement points give two different numbers on the same board, and the difference is often 0.1 mm. |
| Colour and legend | Mask colour, legend colour and whether legend is required on both sides | Mainly a lead-time variable. Unusual combinations may wait for a scheduled batch. |
| Quantity break points | The volumes at which you want to see a price step | Laminate is bought in sheets. The breaks fall where the sheet count changes, and asking for them shows you the real curve. |
Send with the enquiry
- The stack-up, or the impedance targets that determine it, layer by layer.
- The laminate series, or Tg and Td if you are leaving the choice open.
- Copper weight per layer, marked as base or finished.
- Finished thickness with tolerance and the measurement method.
- Whether halogen-free or a specific brand is a requirement or a preference.
Where it goes wrong
- "FR-4" treated as a specification. It is a flame-retardant epoxy family with a wide range of Tg. A quote that names no grade has priced the cheapest sheet available.
- Tg chosen to look conservative. Higher Tg on a two-layer hand-soldered board buys nothing and can cost yield, because the laminate needs more heat to laminate and to reflow.
- Impedance requested without a stack. The factory either invents a stack or ignores the request. Either way the impedance is unverified until you measure a coupon.
- Brand specified after the quote. Naming a laminate brand after pricing changes both the material cost and, often, the press cycle.
Comparing two fr-4 quotes
Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.
- Compare the laminate series by name. Two FR-4 quotes at different prices are almost always different grades.
- Hold the stack-up fixed. A 0.8 mm and a 1.6 mm board are different products and their prices should not be compared.
- Check whether the thickness is measured over copper. It changes the number by more than the tolerance you are arguing about.
- Ask whether the quote uses a branded or an equivalent laminate. The difference is auditable, and worth paying for when your customer asks.
What this page does not tell you
This page does not recommend a Tg. The right value comes from your reflow profile, your layer count and your operating temperature, and the board-type pages are where we explain how those three interact.
Related
- High-Tg laminates: Tg, Td and T260 are three different numbers
- High-Tg quotes: the premium and when it is wasted
- Rogers and RF laminates: the next price step
- Rigid quotes: the panel and the thickness tolerance
Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.