PCB quotes

Rogers PCB Quotes: Series, Stack and Loss Budget

RF laminate is quoted by series, not by the word Rogers. PTFE-based materials need different drilling, desmear and plating conditions from FR-4, and a factory that has qualified one series has not qualified the others. A hybrid stack adds a second process window to the same board.

Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.

Main cost driver
Laminate series, hybrid stack complexity and test method
Typical lead time
2–4 weeks for prototypes, 4–6 weeks for production

ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.

What this quote is priced on

Five to seven variables move the number on a rogers / rf quote. They are not equally important, and only the first two are usually discussed.

  • Laminate series. Hydrocarbon, PTFE and ceramic-filled series behave differently in drilling, plating and dimensional stability. The series is a process choice before it is a price.
  • Dk and its tolerance. A tighter Dk tolerance restricts the sheet range the factory can use, and rejects more material at incoming inspection.
  • Dissipation factor. Lower loss materials cost more. How much you need is set by frequency and trace length, so the loss budget is a design number, not a preference.
  • Hybrid construction. Bonding RF material to FR-4 requires an interlayer adhesive and a press cycle that suits both. Two material systems mean two sets of drill parameters.
  • PTH in RF material. Plated holes through PTFE need special preparation. Where the design allows, avoiding them removes a whole process step and a yield risk.
  • Test coupons and measurement. An insertion-loss coupon and a VNA measurement are part of the product. A quote without them describes a board nobody has verified at RF.

The parameters a factory needs

This is the set that has to be in the enquiry before a rogers / rf price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.

Rogers / RF RFQ parameter set. State every row, or accept the factory's default.
Parameter What to state Why it changes the answer
Laminate series The exact series name and manufacturer, per RF layer Every series has its own drill, desmear and plating process. Naming the series is naming the process.
Dk target and tolerance Design Dk per layer with the tolerance you will accept Dk sets the trace width for a given impedance. Tolerance decides how much material is rejected before a board is built.
Dissipation factor budget The loss the design can tolerate, at the operating frequency Loss budget is what separates a mid-grade hydrocarbon from PTFE. Without it, you are paying for a guarantee you cannot check.
Stack: pure RF or hybrid A section showing which layers are RF and which are FR-4 Hybrid stacks need an adhesive layer and a compatible press cycle, which is a step change in cost and risk.
RF layer thickness Finished dielectric thickness per RF layer Thickness and Dk together set impedance. Quoting one without the other leaves the impedance undefined.
Plated holes in RF material Whether any PTH or microvia passes through RF laminate PTFE needs special hole preparation. Removing or relocating those holes can cut cost more than any negotiation.
Surface finish compatibility Finish type, and whether it must be low-loss or non-magnetic Some finishes add loss at high frequency. The finish is part of the RF path, not a cosmetic choice.
Test coupon and method Coupon design, the VNA used, and the frequency range reported Without a stated method, "tested to specification" cannot be reproduced or disputed.

Send with the enquiry

  1. The laminate series per RF layer, with manufacturer and thickness.
  2. A section drawing showing pure RF against hybrid construction and every bond ply.
  3. Dk and dissipation factor targets with the operating frequency and trace length.
  4. Whether any plated holes pass through RF material, and if they can be moved.
  5. The insertion-loss test method and the coupon you will accept as evidence.

Where it goes wrong

  • "Rogers capability" as a qualification. It is a marketing statement. Without a named series and a loss test method, it says nothing about the process the board will run on.
  • Hybrid stack quoted as pure RF. The bond ply and the second press window are missing from the price, and the boards delaminate at the interface.
  • Dk taken from a datasheet for a different thickness. Effective Dk depends on the laminate thickness and the copper. Using a generic figure puts the impedance off before the board is made.
  • Finish chosen for cosmetics. Some finishes are lossy or magnetic. At high frequency the finish is part of the transmission line.

Comparing two rogers / rf quotes

Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.

  • Compare the named series first. Two "Rogers" quotes for different series are not competing on price; they are different materials.
  • Check whether the stack is hybrid, and whether the bond ply is included in the thickness.
  • Ask what coupon and what instrument will be used to demonstrate loss. A quote that cannot answer has not planned the test.
  • Compare PTH counts through RF material. That single number often explains more of the price gap than the laminate does.

What this page does not tell you

This page gives no Dk or loss figures, because they are series-specific and thickness-dependent. Any number quoted without a series and a thickness is not a specification.

Related

Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.