PCB quotes

6-Layer PCB Quotes: Where Factories Separate

Six layers is where factories start to separate. Below that, most plants are equivalent; at six layers the inner-layer registration, the press cycle and the drill aspect ratio begin to matter, and the cheapest quote often comes from a plant whose six-layer yield is not yet stable.

Lead times are industry ranges, not commitments. Any factory's actual date depends on its queue that week, and on what else is already scheduled.

Main cost driver
Registration capability and lamination cycle count
Typical lead time
5–10 working days for prototypes, 2–4 weeks for production

ChinaPCB.org does not quote boards and takes no commission. This page exists so that the enquiry you send to a factory is complete the first time. Send it yourself — see how to send an RFQ.

What this quote is priced on

Five to seven variables move the number on a 6-layer quote. They are not equally important, and only the first two are usually discussed.

  • Inner-layer registration. Six layers means three inner cores that must align to the same drill. Registration capability is what separates a plant that builds six layers routinely from one that occasionally does.
  • Lamination cycles. One press cycle for the core, one for the outer foil. Each cycle can shift the stack, and the press schedule decides how much of that shift the plant can absorb.
  • Aspect ratio. The same drill diameter at six layers is often a thicker board, so the aspect ratio rises. This is where a design that was routine at four layers becomes constrained.
  • Impedance control. At six layers you usually have reference planes, which means impedance can be controlled. Controlling it requires a stack-up owned by the factory and a coupon to prove it.
  • Yield, not price per square metre. Inner-layer scrap is invisible in a per-area price. Ask what happens to a panel that fails at the press; the answer explains the gap between quotes.

The parameters a factory needs

This is the set that has to be in the enquiry before a 6-layer price means anything. The third column is why each one changes the answer, which is also the reason a quote that skips it is not really a quote.

6-layer RFQ parameter set. State every row, or accept the factory's default.
Parameter What to state Why it changes the answer
Layer assignment What each of the six layers carries: signal, ground, power, and the reference pairs Layer assignment determines the stack, the impedance and whether the design is buildable at the thickness requested.
Stack-up with dielectric thicknesses Copper weight and dielectric thickness per layer, in a section At six layers the stack is the product. Two quotes with different stacks are two different boards at the same layer count.
Smallest via and annular ring Finished hole size, pad diameter and the annular ring you require Sets the registration requirement, which is the main capability difference between plants at this layer count.
Aspect ratio Board thickness divided by the smallest hole, stated by you A ratio above roughly 8:1 changes plating and drilling parameters. Stating it prevents a quote for a board the plant cannot plate reliably.
Impedance and reference layers Targets with tolerance, and which layers are the references Controlled impedance fixes the dielectric thicknesses, which fixes the stack. Selecting it after the stack is set restarts the quote.
Registration tolerance Layer-to-layer registration you will inspect to This is the number that separates a routine six-layer plant from an aspirational one, and it is rarely volunteered.
Assembly reflow peak Whether the board will be assembled, and the peak temperature Reflow constrains laminate choice and copper balance. A board quoted as bare-board may need a different stack once assembly is included.
Quantity and panel size Order quantity, annual volume and the panel you expect Panel size and layer count together decide how the plant schedules the press, which is where the lead time actually comes from.

Send with the enquiry

  1. A section drawing with all six layers, copper weights and dielectric thicknesses.
  2. Layer assignment: which layers are planes and which are signal.
  3. The smallest via with finished diameter and pad, plus the aspect ratio.
  4. Impedance targets with tolerance and the reference layers.
  5. Whether the board will be assembled, and at what reflow peak.

Where it goes wrong

  • Comparing six-layer prices without the stack. A 1.6 mm board and a 1.2 mm board at the same layer count are different products. The price difference is the stack, not the factory.
  • Aspect ratio ignored at the quote stage. The design is quoted, tooled and then rejected at plating. The rework is a redesign, not a discount.
  • Impedance requested as an afterthought. Controlled impedance fixes dielectric thickness, so it cannot be added to a stack that is already priced.
  • Cheapest quote chosen without a registration figure. At six layers, registration is the capability. A plant that cannot state its figure is not competing on the same product.

Comparing two 6-layer quotes

Two prices are only comparable when the parameters above are held constant. Most of the spread buyers see comes from a difference in one of these, not from a difference in factory efficiency.

  • Compare the stack, layer by layer. At six layers the stack is the quote.
  • Ask each supplier for its layer-to-layer registration tolerance. It is the number that predicts whether the boards will pass your inspection.
  • Compare the aspect ratio each one accepted. If one quietly relaxed it, the price is for a different process.
  • Compare what happens to scrap. A quote that assumes a lower yield is not necessarily worse; one that ignores it is.

What this page does not tell you

This page does not say which plants can hold 6-layer registration, because that is a per-factory capability we record on the board-type pages, not a property of the layer count.

Related

Fee structure and editorial independence are described on the about page. What we can and cannot confirm about a factory is on how we verify.