Component library: the part number that does not survive the BOM
What happens to a part's identity between the component library and the placement machine, and which of those handoffs can a buyer see in a factory's published record?
The switching signals in this article
- 01 The library holds nouns An MPN, a symbol, a footprint, a lifecycle state, a stock count. The factory works in batch numbers, date codes, packaging and floor life. The two lists never share a column.
- 02 43 SMT, 18 turnkey, no BOM rule Forty-six profiles list SMT as a service and 21 list turnkey. Across 1,252 capability lines, the number that describes handling a customer BOM, approving a substitute or inspecting incoming parts is zero.
- 03 Five part numbers, none of them a component The phrase appears five times in the directory, always as a PCB part-number throughput — 9,000 to 120,000 a month. It never once refers to a component MPN.
- 04 The clock nobody carries Moisture sensitivity, packaging form and floor life are properties of the bag, not of the part record. No profile and no library row in this directory states any of the three.
The widely circulated outline on centralized component libraries opens with a claim worth agreeing with: the parts library, not the schematic or the layout, is where hardware teams lose the most time. It then lists what a good library does — a part-creation workflow, standardised symbols and footprints, version control on library parts, defined review and approval roles, 3D models that mechanical can check, usage tracking and a live stock figure. Every one of those is an improvement inside the library.
This piece follows one record out of the library instead. A part is created once and used for years, but it is bought, shipped, stored, opened, placed and inspected many times, and each of those events happens somewhere the library does not reach. Between the record and the placement machine there are four handoffs. A buyer can see the first one in a BOM, and the other three only if a supplier chooses to describe them.
The directory gives a starting measure of how rarely that happens. Forty-six of the 131 profiles list SMT among their services; 21 list turnkey, which is the offer to buy the parts as well as build the board. Across the same 131 profiles, the 1,252 capability lines contain no mention of a bill of materials, no mention of an approved vendor list or a substitute, no mention of incoming inspection or moisture sensitivity, and no mention of tape, reel, tray or kitting. Not one profile out of 131 states a rule for handling the parts you send.
A library holds nouns, a factory works in quantities
The mismatch is grammatical before it is technical.
| The record says | The floor says | Where the second value comes from |
|---|---|---|
| One MPN, valid from a date | A batch, a date code, a country of origin | The distributor's label on the bag, printed before the plant sees the order |
| One symbol, one pin mapping | A polarity mark, a pin-1 chamfer, a silkscreen | The fabrication drawing and the assembly drawing, which are separate files |
| One footprint, nominal land pattern | An aperture in a 0.12 mm stencil, plus a resist definition | The stencil file, which the plant generates and you may never see |
| A lifecycle status, Active or NRND | A bag that has been open for eleven hours | The sealed bag's own clock, started by whoever opened it |
| A stock count, refreshed nightly | Reels of 5,000, trays of 250, cut tape of 37 | The minimum packaging the distributor sells in, not the quantity you need |
A library is built to answer “is this the part we meant” and it answers that well. The five rows on the right are answered by people who never open the library: a warehouse clerk, a CAM engineer, a stencil operator, a SMT line leader. That is why the rest of this piece is organised as four handoffs rather than as a list of library features.
First handoff: the part number on the traveller is not your MPN
The phrase “part number” appears five times in the capability tables. All five describe the same thing, and it is not a component.
| Profile and the figure it publishes | Part numbers |
|---|---|
| Jiajietong Shanghai, alongside 12,000 m² a month | 9,000 |
| Kingbrother, annual throughput | 100,000 a year |
| Qiangda Circuit, shipped | 10,000+ a month |
| Stariver Huangshi, group capacity | 2,500 a month |
| Xunjiexing, Zhuhai | 120,000 a month |
Every one of those five figures is a PCB part number: a bare-board design that entered the plant, was tooled, and shipped. Not one is a component. In the vocabulary of the plant, your board is the part, and a 200-line BOM is a document attached to it rather than a set of things the plant schedules.
That is the first handoff, and it is structural rather than careless. A fabricator’s capacity system is organised around panels, layer counts and drill programmes. The components arrive later, on a purchase order raised against your BOM, and the two systems meet in a spreadsheet rather than in a database. When a directory page advises a buyer to send the BOM with the fabrication drawing, that is an accurate description of the interface: the BOM is an attachment you supply, not a record the plant maintains.
The consequence is worth stating plainly. Anything the library knows about a part is invisible at this handoff unless it is written into the BOM or the assembly drawing, because those are the only two documents that cross the boundary. A lifecycle flag inside a library is not a document.
Second handoff: the reel, the bag and the floor-life clock
Turnkey is the service that makes this handoff somebody else’s job. Eighteen profiles list it, and the offer is straightforward: the plant buys the parts, so you do not have to place six distributor orders for a hundred-board run.
What the offer implies is a set of decisions the buyer has just delegated, and none of the eighteen publishes how it makes them. Three of those decisions have a physical deadline attached.
The first is moisture. A part in a moisture-sensitive package absorbs water while the bag is open, and the absorbed water turns to steam at reflow. The level sets the floor life — the hours a part may sit exposed at a given temperature and humidity before it must be baked or discarded. Under J-STD-033 the clock starts when the seal breaks. If the library record does not carry the level, then the buyer who chose the part never knew the part had a deadline, and the plant receives a bag with no stated budget for the interval between opening and reflow.
The second is packaging form. A reel of 5,000 is not a reel of 500, and cut tape is not a reel at all for a line that feeds from a cassette. The minimum packaging quantity sets the overage, and the overage is the difference between a quote and an invoice. No profile in the directory states a packaging form.
The third is substitution. A part goes short, or the distributor ships a different reel of the same family, or the plant’s buyer finds an equivalent at a better price. Whether that is allowed is a one-line rule, and it belongs in the library next to the MPN rather than in a purchase order comment. The directory contains no line describing a substitution rule, an approved vendor list or a second-source policy — not because plants never substitute, but because the rule lives in a commercial conversation and not in a published capability table.
Third handoff: your footprint meets their stencil aperture
The library’s footprint is a nominal land pattern. The plant’s stencil is an aperture with an area ratio, and the two numbers are produced by different people from different conventions.
The directory has almost nothing on either. One line mentions a pad dimension, and it is a micro-via pad on a flex substrate rather than a land pattern. Stencil, solder paste and aperture appear zero times. What the capability tables do describe is placement: 19 lines across 16 profiles, and they are all about machines.
| What is published | Example from the directory | What it does not tell you |
|---|---|---|
| Placement accuracy | ±30 µm at 3 sigma, with a 10 µm X-Y axis, on a 510 × 510 mm panel | Whether your 0402 land pattern matches the aperture the plant will cut |
| Component size range | 0.3 × 0.15 mm up to 120 × 90 mm, 30 mm maximum height | Which package families have a qualified footprint in the plant's own CAM library |
| Line count and throughput | 100+ SMT lines group-wide; 25.8 million populated flex pieces a year at one Zhuhai site | Whether the line that runs your order has seen this package before |
| Scope boundaries | An IATF certificate whose scope reads "printed wiring board manufacture only; no SMT or PCBA assembly" | Nothing — this is the honest case, and it is the only one that names its boundary |
The last row deserves attention because it is the exception. One profile publishes a certification scope that explicitly excludes assembly, which means the buyer knows the plant will not touch components at all. The other fifteen describe what the machines can do without saying where the work stops. A placement accuracy of ±30 µm is a machine capability; it is not a statement that a specific land pattern will produce an acceptable joint, because joint quality depends on the aperture, the paste, the reflow profile and the pad finish, none of which are in the same table.
For a library, the actionable part is narrow. If the plant adjusts a land pattern for its own process, that adjustment is a real engineering decision and it should come back to you as a drawing change rather than as a line that runs. The review that catches it is the CAM review, not the library’s approval workflow.
Fourth handoff: proving the right part landed
Assembly inspection answers questions about placement, not about identity. Optical inspection finds a missing part, a rotated part, a tombstone and a bridge. It does not know whether the 10 µF capacitor in position C14 is the one in your library or an equivalent with a different voltage rating and the same case size, because the two look identical under a camera.
The directory has two lines describing AOI, X-ray or in-circuit test, and they describe equipment rather than acceptance. First-article inspection appears zero times, and the phrase carries weight here: a first-article report is the one document that connects a BOM line to a physical part on a specific board, signed by somebody who checked. Without it, the chain from library record to placed component has no link that a buyer can audit.
What closes the chain is unglamorous and entirely absent from the profiles: the distributor label on the reel, a photograph of it, and a line in the first-article report recording the date code that was consumed. None of the 1,252 capability lines mentions a label, a barcode or a date code.
Five fields to add, and who owns each
If the library is the only place where a part’s identity is written down, then the fields that cross the four handoffs belong there. These five are chosen because each one answers a question the factory would otherwise have to guess.
| Field | The question it answers at the plant | Profiles that publish it |
|---|---|---|
| Moisture sensitivity level and floor life | How many hours do we have between opening the bag and reflow, and does this part need a bake? | 0 |
| Packaging form and minimum quantity | Can this run on a cassette, and how much overage will the quote carry? | 0 |
| Substitution rule, in four levels | May we ship an equivalent if the exact MPN is short, and who signs? | 0 |
| Land pattern source and any process adjustment | Is this pad geometry nominal, or the version this plant runs? | 1, and it is a via pad |
| Lifecycle state with a last-buy date | Is the reel we are about to consume the last of a discontinued line? | 0 |
The substitution field is the one that needs a decision rather than a data entry, so it is worth specifying in four levels: exact MPN only; same die in a different package; same electrical family from a named list; any equivalent in the same package and rating. Written as a field, it turns a substitution into a recorded choice. Written as a comment on a purchase order, it becomes a preference that a buyer may not read.
The last-buy date has a similar property. A lifecycle status of Active is a database value that can sit unchanged for years after the manufacturer has stopped the line. The date is the part that becomes true or false.
What a better library cannot fix
A library is a single source of truth about intent, and that is genuinely valuable: one MPN behind one symbol removes the duplicate, the mismatched model and the two engineers who each fixed the same footprint. The six practices in the outline are worth adopting for that reason alone.
They stop at the boundary because the factory’s truth is not centralised and cannot be. The purchasing desk holds the distributor relationship, the warehouse holds the bags, the SMT line holds the reels, and the QC desk holds the section. Four places, four records, none of them a library. A library that carries the five fields above does not centralise those records; it gives each of them a reference to point at.
There is one thing no field can do. Substitution is a transfer of risk, and a library can record which risk you accepted without deciding it for you. A buyer who writes “exact MPN only” onto a part has chosen a schedule risk; a buyer who writes “any equivalent” has chosen a technical risk. Both are legitimate, and neither is a data problem. What the record buys is the ability to say afterwards which one was chosen, by whom, and on which revision — which is the same reason the revision on the board needs a document behind it.
The parts library is the right place to be precise about parts. It is the wrong place to assume the precision travels.
Source: service fields and capability tables published by the 131 profiles in this directory, read 2026-11-17. J-STD-033 floor-life rules and the four substitution levels are standard practice, not profile figures.
Questions this article answers
Does a centralized component library stop the wrong part being placed?
It stops the wrong part being drawn. A single MPN behind a single symbol removes the duplicate and the mismatched footprint, which is the failure a library is designed for. It cannot reach the placement machine, because the machine is fed from a reel whose label is the only link back to your MPN, and nothing in the library travels with that reel.
What should a component record carry so a factory can plan around it?
Three fields that describe the package rather than the part: the moisture sensitivity level with its floor life, the packaging form with the minimum order quantity, and the substitution rule you will accept. All three are properties of how the part arrives, and all three change what the plant has to do with it before reflow.
Who is responsible for moisture-sensitive parts before assembly?
The party holding the bag. Under J-STD-033 the clock starts when the sealed bag is opened, and the level sets the hours available at a given humidity. If the library does not carry the level, the purchasing decision was made without it, and the plant receives a part with no stated budget for the time between opening and reflow.
Can a factory substitute a part without asking?
That is a contract question, not a data question, and the profile set does not answer it: no capability line in 1,252 mentions substitution, an approved vendor list or a second-source rule. What a record can do is make the answer explicit in four levels, from exact MPN only to any equivalent in the same package, so that a substitution is a decision somebody made rather than a delivery that happened.
Is turnkey the same as consigned material?
No, and the difference decides who carries the risk on the reel. A turnkey profile buys the parts, so it chooses the distributor and absorbs the shortage. A consigned order sends your own reels to the plant, so the shortage is yours and the plant's exposure is limited to handling. Eighteen profiles in this directory list turnkey among their services; none publishes which of the two models its quotes assume.