Factory profile · Public sources reviewed

Huaqiu PCB

深圳华秋智联股份有限公司 · Shenzhen, Guangdong · Founded 2011 · Not listed

Huaqiu states its layer ceiling three ways across its own properties. Its UL file also sets a conductor width that the marketing table never mentions.

Huaqiu is a platform with captive factories rather than a single plant, which makes it convenient for a prototype and awkward for a qualification. Use it for a 4- to 12-layer board where the online configuration is enough, and get the layer ceiling and the UL construction confirmed in writing before promising either to your own customer.

Identity and record

Only entries that were checked against a source are shown. A blank field means we have not confirmed it, not that it does not exist.
Registered name (Chinese) 深圳华秋智联股份有限公司
Registered name (English) Shenzhen Huaqiu Zhilian Co., Ltd.
Founded 2011
Listed Not listed
Headquarters Shenzhen, Guangdong
Production sites Jiujiang (Jiangxi) · Shenzhen · Jiangmen (Guangdong) · Changsha (Hunan) · Chenzhou (Hunan) · Huzhou (Zhejiang)
Official website https://www.hqpcb.com
Evidence levelPublic sources reviewed
Last reviewed2026-11-11
Registered entity and published production sites Registered entity Huaqiu PCB and 4 named production sites, from the disclosures cited on this page. PUBLISHED RECORD Huaqiu PCB 深圳华秋智联股份有限公司 Founded 2011 · Not listed Jiujiang Jiangxi Shenzhen Site 2 Jiangmen Guangdong Changsha Hunan +2 more sites named in the profile Source: disclosures cited on this page
Entity and footprint map. Huaqiu PCB and the production sites named in the disclosures cited above.

Three ceilings for one question

Ask Huaqiu how many layers it can build and you get three answers. The hqpcb.com banner says 32 layers with 3-stage HDI. The order-configuration page offers a layer selector that stops at 20. A company release about the HDI line describes “20-layer high-end HDI”.

Two of these can be reconciled if the 32-layer capability sits on a line that the online configurator does not expose, and that is probably the explanation. But a buyer cannot confirm it from the outside, and the gap matters: a 24-layer design that the banner supports and the order form does not will need a manual quotation, which means a slower answer and a different price.

The practical rule for a platform supplier is to treat the online ceiling as the real ceiling until a human confirms otherwise in writing.

Platform, then factories

The parent, 深圳华秋智联股份有限公司, runs an EDA tool, a DFM checker, a component mall and the PCB ordering front end. Fabrication happens in subsidiaries: the Jiujiang plant, which is the volume site at 120,000 m² per month, plus sites in Shenzhen, Jiangmen, Changsha, Chenzhou and Huzhou. Chenzhou is described as a PCBA plant, not a PCB plant.

That structure is why the five “bases” cannot be read as five PCB factories. It is also why the order pages do not say which subsidiary books and builds an export order. For a prototype this is irrelevant. For a qualification it is the first question: the certificate, the process traveller and the invoice should all point at the same legal person.

The UL file does not cover the headline capability

UL file E469747 covers designations HQPCB1 through HQPCB4 with a minimum conductor width of 0.13 mm, last updated in June 2022. The capability table claims 3/3 mil standard, which is 0.076 mm, and 2.5/2.5 mil at the limit.

0.13 mm is 5.1 mil. So the UL-listed construction is a wider-trace board than the marketing table leads a buyer to expect. That is not unusual, and it is not a defect: UL recognition is granted per construction, and a factory can build finer lines than the UL file covers as long as the customer does not need the UL mark on that board. But if your product needs the UL mark, the construction you order has to sit inside the file, and 3 mil traces do not.

Ask which UL designation your stack-up will carry, and get the minimum conductor width for that designation in writing. This is the check that separates a UL claim from a UL listing.

Where the volume actually is

The Jiujiang park was built with a stated split: Shenzhen small-batch plant at 20,000 m² per month, Jiujiang mass-production phase 1 at 100,000 m² per month on a 205-mu site. The Jiujiang figure has since been quoted at 120,000 m² per month, and the plant was named a provincial advanced smart factory in 2026.

The pattern is familiar in this segment: small batch in Shenzhen, volume in a lower-cost province. If your order grows from 50 boards to 5,000, expect it to move, and expect the move to be a process change rather than a capacity change. Write the transfer rule into the supply agreement.

How to use this profile

Use Huaqiu when the value is in the workflow: DFM feedback before you order, a component mall attached to the assembly quote, and a price you can see without an email thread. Those are real advantages for a small hardware team.

Do not use the platform as evidence of factory capability. For anything that has to be qualified, ask for the Jiujiang plant’s certificate set, the UL designation for your construction, and confirmation that the order will not be routed to a partner workshop. None of those three answers is on the website.

What is not established

The English legal name of the parent is a translation, not a registered English name, so a contract should carry the Chinese name and the credit code. The IATF 16949 certificate number and scope are not published. The UL holder entity is not named on the extract, only the designations. Employee count, revenue and per-plant layer capability are all unpublished, and the 2022 date on the UL file means its currency should be confirmed rather than assumed.

Published limits

Every value below is quoted as published by the company or a public record.

ParameterValue as published
Maximum layer count, banner claim 32 layers, 3-stage HDI
Minimum line width and spacing 3/3 mil standard, 2.5/2.5 mil at the limit
Minimum laser-drilled hole 0.075 mm
HDI structures 1-stage, 2-stage stacked, 3-stage any-layer; boards of 4–32 layers
HDI prototype lead time 4-layer 1-stage HDI in as fast as 7 days
Surface finishes at order entry Leaded HASL, lead-free HASL, ENIG, OSP
Copper weight at order entry 1 oz, 2 oz, 3 oz, 4 oz
Monthly capacity, Jiujiang plant 120,000 m² per month

Certifications on record

A certificate covers a legal entity and a site, not a brand. Scope and expiry are recorded where published.

StandardWhat the record shows
UL File E469747, designations HQPCB1 to HQPCB4, minimum conductor 0.13 mm, last updated 2022-06-20
ISO 9001 Stated on the home page; certificate PDF linked from the same page
ISO 14001 Stated in the same certification paragraph
IATF 16949 Described as the automotive certification; no certificate number or site scope published
CQC Listed among the certificates with a PDF link

Ask this factory for a quote

Send one technical package and compare the replies. The RFQ checklist lists what to include; the quote specifications say which parameters change the price for the process you are buying.

Request a quote

Source and review conventions are described in how we verify. Corrections can be sent through the contact channel.